Recent content by crippss

  1. C

    TEA20 Paint Colour Code

    I'm looking for the TEA20 grey colour code. I have found a cross reference form already but, here in Canada, the colour codes don't exist or if they do they're a different colour. Does anyone have an updated or North American colour comparison?
  2. C

    TE20 hydraulic arms lifting/lowering problems

    Thank you for the comments. I have a good friend who has an 8N so I believe somewhere he's engrained the control limiting into me haha. I'm only 25 so have a lot to learn about these creatures!
  3. C

    TE20 hydraulic arms lifting/lowering problems

    Awesome!!!! Super appreciate the response! Out here in my neck of the woods there's very little fergie related so getting questions answered and parts are hard to come across. I'll have to see what I can conjure up. The chains (from what I can see) go from the rocker bracket to the end of the...
  4. C

    TE20 hydraulic arms lifting/lowering problems

    Awesome!!!! Super appreciate the response! Out here in my neck of the woods there's very little fergie related so getting questions answered and parts are hard to come across. I'll have to see what I can conjure up. The chains (from what I can see) go from the rocker bracket to the end of the...
  5. C

    TE20 hydraulic arms lifting/lowering problems

    Hello! I am hoping someone could shed some light for me. I have finished rebuilding the engine on my '53 TEA20. And now I'm onto the hydraulics. The hydraulics work! However, they're either shooting up or dropping. There seems to be a spot where they'll either disappear into the ground or...
  6. C

    TE20 Carb/manifold gas problem

    I gave the carb a clean with carb cleaner before it went back together. Made sure everything was in top shape. It only blows a bit of gas out the gasket when it's basically on its last hurrah when I take my finger off the starter switch. I know it's not the valves or there related as...
  7. C

    TE20 Carb/manifold gas problem

    So I've recently done a bunch of work to the TE20. Reseated the heads. Cleaned it inside out. Put it together last night and worked a charm. Just have the rad to put on. No backfiring. No spluttering. Was great. This morning I went to try it and the starter got red hot (like it does when the...
  8. C

    TE20 carb/revving/throttle problems

    After taking the valves out it was obvious why there was back firing. Both the intake and exhaust seats were destroyed. So much pitting. I got some valve grinding compound and proceeded to reseat the valves. Worked awesome. All seated nicely. Cleaned it all in petrol and put everything back...
  9. C

    TE20 carb/revving/throttle problems

    I think I may have found the culprit to the poor engine running. The valves in the first and fourth cylinder aren't seated properly due to crud so they're being taken out and cleaned one by one. The second thing is that a friend pointed out the sooty 'blow out' marks on the side of the gasket...
  10. C

    TE20 carb/revving/throttle problems

    So I'm in the process of taking it apart. Next step is to take the front off and check the throttle parts. Figured I'd start from the ground up. I have the top off and the pistons are a little charred but nothing major, however there's quite a lot of oil in the sections where the valves are...
  11. C

    TE20 carb/revving/throttle problems

    So I've tried a bunch of things. Wiring is all good. Set the carb settings to what I found from a manual. Sprayed carb cleaner into the carb whilst running and it ran well and not back firing a whole lot. However when it did backfire gas was blowing out the carb/intake gasket. I can run it with...
  12. C

    TE20 carb/revving/throttle problems

    Double checked the wiring, the combination is correct. The way I said it was right, just backwards haha but it is correct. The engine was running rough still before the carb kit and I figured it may help, and it certainly didn't do a whole lot of good. I'll have to play around with a few...
  13. C

    TE20 carb/revving/throttle problems

    Yes! You're correct. That is how I have it set up. I will double check though to make sure but I'm pretty certain that's how it's wired. That would help the backfiring but not the high revvin issue. The front looks pretty easy to take apart so I'll probably take a stab at it anyway.
  14. C

    TE20 carb/revving/throttle problems

    Awesome. Thanks for responses. I'll definitely try the carb problem. I know it needs a good tuning and hopefully that'll help diagnose the vacuum problem. I have a full gasket kit and was hoping I wouldn't have to use it, but if the fronts coming off the rest of its coming apart. I'll try and...
  15. C

    TE20 carb/revving/throttle problems

    Theres an old chap up the road with the same year so I took his distributor/condenser off his and put it on mine but the same problem occurred. The wiring is all in the correct order (1,2,4,3). The cables and plugs are brand new. Nothing in the cap is cracked or damaged. I ruled the...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top