(800) 853-2651
SHOP NOW

Recent content by Curtis

Yesterday's Tractor Forums
  1. C

    Oliver plow - looking for 12

    This message is a reply to an archived post by plowman on May 03, 2018 at 15:10:16. The original subject was "Re: Oliver plow looking for 12". I?m still in need of one more NC225-12 moldboard. Can anyone recommend a source?
  2. C

    Oliver plow - looking for 12" moldboards

    J, I’m located in SE PA, but the plow came from NY. I’m not sure how common the 225 bottoms were in that area. The frame doesn’t show much wear or abuse, but the bottoms were heavily worn (apparently from rocky/gravel soil condition) including the rear edge of the moldboards which is worn to a...
  3. C

    Oliver plow - looking for 12" moldboards

    I'm looking for NC225-12 moldboards for a 102 Plowmaster plow. Can anyone recommend a source? I need two. Can be new or good used. I've checked my local dealer and a number of aftermarket sources and can't seem to find any new 12" moldboards in the 225 (or 425/625 style for later plows)...
  4. C

    Oliver 70 engine knock cont.

    Hey KenL - just checking back in to see if the NOS timing gears fixed your problem, or if you've found something else...
  5. C

    Oliverfleetline throttle

    I recently purchased mine from McMaster-Carr - catalog number 9434K49.
  6. C

    Oliver 70 engine knock cont.

    Ken, please keep us updated on how this works out... sounds like you are a step or two ahead of me, so I'm quite interested. I'm in the middle of tearing down the front end on mine. I have quite a bit of backlash at the governor gear (I don't have a dial indicator, but by using feeler gave...
  7. C

    Oliver 70 timing gear update - (mike french)

    Thanks for the feedback J. My engine is a 3-gear. This tractor sat for 30+ yrs and was locked up when my Gpa and I started restoration 15 yrs ago. We freed and rebuilt motor at that time (rings, rod and main bearings, I think we did wrist pin bearings, but honestly can?t recall). We ran motor...
  8. C

    Oliver 70 timing gear update - (mike french)

    This message is a reply to an archived post by mike french on November 09, 2013 at 03:27:20. The original subject was "Oliver 70 timing gear update". Mike French, are you able to share how you diagnosed the knock as timing gears? Were you able to find new gears, or did you replace with better...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top