(800) 853-2651
SHOP NOW

Recent content by Cybball

Yesterday's Tractor Forums
  1. C

    PTO Lock Pin Spring

    Thanks. I will try that. Thinking through that idea, it should work.
  2. C

    PTO Lock Pin Spring

    The pin has to go in the orc first. It wouldn’t have clearance to go through if the spring was on first. The pin fits perfectly (not same manufacturer). Just need to figure out how to get the small end of the spring over the knob on the pin.
  3. C

    PTO Lock Pin Spring

    I recently lost a pto lock pin off of a new removable overdrive clutch. I found the replacement. My question is, how do you get the spring on the pin? I get that the end of the spring is smaller than the end of the pin so it holds it on. Is there a trick to getting it on ? I have been...
  4. C

    Ford Jubilee plow question

    This. Thank you. I don’t use a pto or the overdrive for plowing. It’s just hitting my plow. I ordered a removable overdrive for when I do some mowing. I really appreciate the help and will be back with more questions related to my tractor eventually. Fun project!
  5. C

    Ford Jubilee plow question

    I just ordered the removable clutch. Problem solved, hopefully.
  6. C

    Ford Jubilee plow question

    Wow. Yes, I would have gone that route had I known. Thanks
  7. C

    Ford Jubilee plow question

    i will get some pics soon. Sounds like you had this situation. I may have to take it off to plow, then reinstall. Sucks but I won’t plow more than once a season.
  8. C

    Ford Jubilee plow question

    Pto clutch attaches with a roll pin. I would have to unscrew both grease zerks and punch the roll pin out. It isn’t made to quickly unhook it which would make it easy.
  9. C

    Ford Jubilee plow question

    This isn’t with the pto hooked up. It’s just the overdrive clutch. That does extend the pto shaft. Back then, they weren’t using a clutch so probably not an issue originally. I could just remove the clutch but like having when I will be brush hogging.
  10. C

    Ford Jubilee plow question

    I have a 53 Golden Jubilee. I installed a PTO overdrive clutch for a brush hog. I recently bought a Ferguson 2 bottom plow. I hooked it up yesterday for the first time to move it into the shop to do some work on it. I saw when I lowered the plow that the plow frame is hitting about an...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top