-
D
14.9-28 tire pressure
What is a good tire pressure to run in a 14.9-28 Firestone 151 tires on 13 rims. Pulling 3500-4500 lb classes- DanH
- Thread
- Replies: 4
- Forum: Tractor Pulling
-
D
Magneto to distributor swap Farmall H
We use the Tractor for plowday and some antique Tractor pulling. Thought it might give a little more horsepower. Do you think it?s better to stay with the magneto then.- DanH
- Post #1
- Forum: Farmall, International & McCormick
-
D
Magneto to distributor swap Farmall H
I believe it is a cut out- DanH
- Post #1
- Forum: Farmall, International & McCormick
-
D
Magneto to distributor swap Farmall H
Want to change from a magneto to a distributor with a electronic ignition. What wiring will I need to change? Also where is a good place to send the distributor to be rebuilt I purchase it used off eBay and would like to have it gone over. Any help and advice is greatly appreciated- DanH
- Thread
- Replies: 15
- Forum: Farmall, International & McCormick
-
D
Ford 950 governor shaft oil seal
Is replacing the governor shaft oil seal a difficult job. Anything special to do or look for. -
D
172 compatible with a 740
Would a 172 bolt right up in place of the 134 engine. Also what about a 192. Any modifications needed -
D
Ford 961
Any body using a Ford 961 for antique Tractor pulling?. Do they make good horsepower.- DanH
- Thread
- Replies: 6
- Forum: Tractor Pulling
-
D
Farmall super c or Farmall 200
What does any body think about a super c or a Farmall 200 as a 3000 and 3500 puller. Are the any good and how much power can you get out of them. Thanks Dan- DanH
- Thread
- Replies: 10
- Forum: Tractor Pulling
-
D
John Deere 620 Flywheel End Play
Got the flywheel on more now it is good at .008 thousands Thanks everyone- DanH
- Post #1
- Forum: John Deere
-
D
John Deere 620 Flywheel End Play
Having some issues with setting the flywheel end play on my JD 620. Took it apart to replace the broken inner thrust washer on the flywheel side. Didn?t check end play before I took it apart didn?t have a dial indicator. Put everything back together and following the the manual on setting the...- DanH
- Thread
- Replies: 6
- Forum: John Deere
-
D
John Deere 620 friction disk replacement
Yes you are correct. It was early this morning when I posted this- DanH
- Post #1
- Forum: John Deere
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy