(800) 853-2651
SHOP NOW

Recent content by DanH01

Yesterday's Tractor Forums
  1. D

    ford f150

    Chances are the other posters are right and the source of the miss is in the Dist, plug wires, or even a plug itself. I"ve got a 1989 F150 with a 4.9. It was old when I got it and had over 125000 miles on it. Ran ok but had a miss. Which didn't bother me so much as I thought it was a wire or...
  2. D

    OT NRA

    ""The tone of your message seems to be one of a person who is genuinely concerned but I do not believe that you have really thought this through to its logical conclusion based on history of so many other governments which have limited trade and ownership of weapons among its citizens. There is...
  3. D

    OT NRA

    Never said that I was the most educated. So they"re from the Declaration and Bill of rights. The Constitution frames the government to protect those so close enough.
  4. D

    OT NRA

    No, I don"t believe that. If they want a gun bad enough they"l get one. I was just stating that some of the legislation I"ve read about would make it more difficult for shipments of weapons to get stolen by making the manufacturers, distributors and retail outlets more accountable. They would...
  5. D

    OT NRA

    You know I"m a proud vet. Served 8 years defending the Constitution and as I recall there is more to it than the 1st amendment. There"s some high highfalutin language about government by the people for the people and something about protecting liberty, property, Freedom and Lives. The Nra...
  6. D

    electric conversion kit

    Scott.. You"ve got to be careful where you step on this topic. As some of the posters have said there are some very good reasons to do the conversion and good reasons to leave it 6v. And since you said that you mainly use it in the winter when most any vehicle is a little harder to start. Being...
  7. D

    Sickle bar mower

    Besides what the other posters mentioned unless you have the Zane Thang installed you won"t have position control so will have to use limiter chains. And at 7 feet there might be some bounce at the end of the bar that could cause an uneven cut which isn"t too noticeable. With just a spring and...
  8. D

    Question about 8n or 9n or jubale

    Anyone of those tractors IF in real good operational condition can do those things except the hay bales. Most round bales are too heavy for them to lift and effectively move around. The snow plowing and bush hogging and even the post hole digger are no problem as long as you have the additional...
  9. D

    Is this a bad idea?

    Anything could happen and you could "if" yourself somemore gray hairs on parking like that. However with the bucket and boxblade down tranny in 1st and brake pawls on even though there is always risk seems like you minimized it pretty good. Couple of things I"ve learned on my place where the...
  10. D

    OT Tree Planting

    Korn....Since they are bare root I"d get some containers w/drainholes and line them with burlap or something similar. Put several inches of Potting soil in"em. Find the least fertlized soil ya can. Your local supply should have a number of different brands with different additives. Put the trees...
  11. D

    Brush Hog Mower for 8N Ford

    In a word......Yes. I have a 5 footer Brand unknown that was retired from the state road dept. I bought it at auction for a low price 5 years ago. After some TLC it has cut well and will probably outlast me.
  12. D

    running a shredder 9n sherman

    I"ve found with my 2N with a Sherman step up that it"s better to keep it in standard and first or second at 3/4 throttle. The pto speed is determined by the engine speed. Most bush hogs run around 540 rpm which is approximately 3/4 throttle or abt 1500 rpm. Your hog can operate at lower rpms...
  13. D

    must sufficate to shut down

    Look for the search box on your page (mine is the upper righthand corner) Since you have a 8n just type in 8n wiring diagram. You"ll get a list of choices. Just scroll through them till you find one that best fits your situation and click on it. At the end of each choice it says which forum that...
  14. D

    Sliding top link VS solid top link

    Oh well I tried. Just copy and paste the link in your location bar to get there. Or we'll try again. Untitled URL Link
  15. D

    Sliding top link VS solid top link

    That part underneath is part of a swinging drawbar kit. Don"t know if they were OEM or dealer installed later. Here is a link that should shed some light on it if it works. http://www.ytmag.com/cgi-bin/viewit.cgi?bd=nboard&th=700888
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top