(800) 853-2651
SHOP NOW

Recent content by Daniel Bohnenkamp

Yesterday's Tractor Forums
  1. D

    wondering what brand and model this ripper is?

    Wondering what brand and model this ripper is? I am needing to replace the points on it. The point have 2 bolts in them to hold them to the shank. Thanks in advance
  2. D

    What is this Ripper

    none of them will fit my shanks, any ideas on a make and model?
  3. D

    What is this Ripper

    I am not sure that any of those will fit, the ones I have have 2 bolt holes on the bottom to attach it, and the wear shin attaches on the top of it
  4. D

    What is this Ripper

    wondering what brand and model this ripper is? I am needing to replace the points on it. Thanks in advance
  5. D

    2950 John Deere

    cross valve, I did look in the fill hole and nothing is spraying, I am going to remove the filter and see if there is any junk in it and try to find the other screen to see if there is anything in it
  6. D

    2950 John Deere

    I put a new valve and on the out put of the svc control "box" to run the loader. I also had both control boxes rebuilt, I will get it hot again and look in the filler hole. it does have a cab and mfwd the mechanic had it running at his shop for over 6 hours and never got hot, just when...
  7. D

    2950 John Deere

    everything has been pressure washed. I ran the tractor pulling the disc for about 10 hours and that's when I started noticing weird hydraulic issues, such as the loader shaking when trying to raise it or curl it, steering wheel would develop a lock spot and then suddenly the wheels would turn...
  8. D

    2950 John Deere

    So I have a 2950 was pulling a 10 foot offset disc and it got so warm after an hour that moving the loader up and down would almost kill the tractor. temp readings of the engine oil was about 200 the hydraulic system at several points was over 180. 3 point still raises and lowers SVC still...
  9. D

    4020 Clutch

    Thank you for all your help and suggestions, it turns out there is oil on the clutch, I can only hope it is from the crank seal
  10. D

    4020 Synco Stuck

    Thank you for all your help, it turned out to be the shift station on the dash was stuck just have to remove the snap ring and realign everything.
  11. D

    4020 Synco Stuck

    how do you remove the shift levers?
  12. D

    4020 Synco Stuck

    I have a 66 4020 and the transmission is stuck between 3 and park not real sure how that happened but now cannot shift it anywhere tried to rock the tractor with the loader but that didn't help either so is there a simple way to get the shifter to move again?
  13. D

    4020 rear remotes

    it is a 66 and have one set and a has a loader on a separate set for the loader. i have just seen a lot of 4020's with dual set and was wondering how hard it would be
  14. D

    4020 rear remotes

    How hard is it to add a second rear remote to a 4020? Is it as simple as adding the valves and then plumbing it to a set location and adding a lever?
  15. D

    4020 Clutch

    so is there any adjustments? or at this point it is replacing the clutch? or what would have to be done?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top