(800) 853-2651
SHOP NOW

Recent content by Danielfire50

Yesterday's Tractor Forums
  1. D

    MF 30E Transmission Pump rebuild question

    I would replace that pump if it was mine.It looks wore out to me and I don't think the bushing below the seal was meant to be replaced. They are readily available for less than 300 dollars.
  2. D

    50a Loader Dip stick length

    This is the dip stick out of my 50a. 11 3/4 long 7 3/8 to full 9 7/8 to add quart.
  3. D

    Splitting removing engine from a MF50A Backhoe

    I believe the bolts are 7/16nc. It will be easier to remove the whole backhoe unit than it is to remove just the boom.
  4. D

    Battery Powered SawsAll

    Makita is worth looking at. They are made well and have the largest selection of cordless tools available.
  5. D

    MF 50A transmission shifts

    Have already checked the petal linkage to make sure it's adjusted and working properly? Being that the reverse stops working after 30 minutes I'd guess that there are some dried up seals, a worn out/broke sealing ring, or worn out clutches in the reverse clutch pack. A system pressure...
  6. D

    MF 50A transmission shifts

    Is this an instant reverse transmission or manual shuttle.
  7. D

    MF50 industrial control functions

    When you pull plug number 2 most of the fluid that can drain from the torque converter will. You can pull plug number three after the pan is off to clean the magnet.
  8. D

    MF50 industrial control functions

    Also would be a good idea to replace the o-rings on the charge pump pickup tube while you have the pan off.
  9. D

    MF50 industrial control functions

    Yes that pan has to come off to get to the screen. The plug in the front that is not accessable has a magnet in it and is directly below where the torque converter charge pump pickup tube connects to the pan. The 50a has a common reservoir some earlier models had front and rear reservoir...
  10. D

    MF50 industrial control functions

    That accelerator fork is an older design I think. The 50a has separate forward and reverse peddles. The brakes are also separate and mechanical. The serial numbers in the US don't include the model.
  11. D

    MF50 industrial control functions

    The 50a has a different front end loader design and is usually has a center pivot backhoe. All pictures of the 50b have the side shift backhoe. Fyi there should two filters for the instant reverse transmission. One is the suction filter the other filter is on side of the tractor. You have...
  12. D

    MF50 industrial control functions

    Im stumped. It looks to have more features than a 50a has. It does look a lot like a 50b.
  13. D

    MF50 industrial control functions

    I think you have to post a certain number of times on the forum before you can put up pictures. I have a MF50a and the controls sound a lot different. The knob by the dipstick could possibly be the diff. lock. As far as the sound you posted about earlier I have no idea.
  14. D

    Massey Ferguson TLB

    The long lever in the middle is for transmission gears 1&2 The shorter one is high low range. Yes the long right side is the diff lock
  15. D

    Mf40 no reverse

    There are a number of possible causes for no reverse on an instant reverse. First is to check the lever on the bell housing. It should move equally forward and backward by the forward and reverse pedals. If it moves as it should then it's an internal issue and the tractor will need to be split...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top