(800) 853-2651
SHOP NOW

Recent content by dannyidp

Yesterday's Tractor Forums
  1. D

    Ford 655 not charging until revved up.

    I have a new alternator on my Ford and I noticed the alternator will not start charging unless I rev it really high after that it will charge at low idle. Tachometer also will not work unless I rev it high but once I rev it all is good even at idle. What could possibly be the issue here?
  2. D

    Ford 5000 remotes

    Yes it has a single spool remote valve that has never been plumbed. But I've got it figured out now. I have a bracket like you have in your second and third photo but I don't have that kind of box to bolt it too. Where did you get those?
  3. D

    Ford 5000 remotes

    Thanks fellas for all the info I went to Tractor Supply and they had the 1/2 Npt male and female Pioneer fittings so I'm good to go.
  4. D

    Ford 5000 remotes

    Do you think the half inch Pioneer Style female fitting will fit the fitting up above? It looks like it measures almost 7/8
  5. D

    Ford 5000 remotes

    Thanks for the info
  6. D

    Ford 5000 remotes

    Hopefully someone can help I know bolt and nut threads but I'm not sure what's going on here. I ordered the hoses through Yesterday's Tractors and female fittings they sent me male fittings that doesn't fit the end of the hose. I'm guessing the end of the hose is 1/2 NPT? I don't have a clue...
  7. D

    Ford 5000 remotes

    Yes I have the single spool valves and everything it just looks like no one ever ran hoses.
  8. D

    Ford 5000 remotes

    Okay I found a hoses but I need to be for sure which coupler I need to fit this. Thank you
  9. D

    Ford 5000 remotes

    I have a remote cylinder on my 5000 with no hoses. Can someone direct me to a link where I can get just the hoses and possibly the bracket for the rear? I could go to the hydraulic hose shop but I'm not sure about length TPI Etc. I really need these ASAP thanks
  10. D

    655D batteries temperature sensor.

    Hey is there any way to bypass the battery temperature sensor on this Ford? Do you know what the ohm readings should be at 80 Fahrenheit? Thanks guys
  11. D

    268 injection timing help...

    To simplify this question does anyone know the degrees this engine should be running? I have a 256 that runs at 19 but I'm not sure about this 268.
  12. D

    268 injection timing help...

    Yes I'm pretty sure the rings have seated.
  13. D

    268 injection timing help...

    Hello everyone I rebuilt a 95 New Holland 268 engine I now have 50 hours and it's still hazing at idle with unburnt fuel. The book was very vague on timing the pump. What I did was used a dial indicator got the #1 on top dead center lined up all my gears and installed the injector pump with the...
  14. D

    655d sheared oil pump.

    I have been Building engines a long time and I have never seen this happen. I'm just lucky I caught it in time.
  15. D

    655 bad hydraulic noises

    That was the first thing I checked. I may need to post a video because I've never heard hydraulic noises like this and it's on all the cylinders.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top