(800) 853-2651
SHOP NOW

Recent content by Darrin Williams

Yesterday's Tractor Forums
  1. D

    MF65 no hydrualic pressure

    I got the ball busted loose. i"ve cleaned everything out and it appears it"s all working correctly now. thanks for following along on this pain in the rear situation over one stinking stuck steel ball. that"s murphy for you.
  2. D

    MF65 no hydrualic pressure

    ok i got the lever off. there was a roll pin on the pivot point. now i see there is a ball inside the fork that is supposed to let you know when it"s in the locked out position. problem is the ball won"t budge. i screwed the handle out and i can see there is a spring inside the housing that the...
  3. D

    MF65 no hydrualic pressure

    thank you. I"ve gotten the hydraulics to work now i"m trying to figure out why the left lever will not move. it"s frozen in place. i knocked out the roll pin and manually depressed the shaft into the valve and that got the external hydraulics to work. i can manually pull it back out and that...
  4. D

    MF65 no hydrualic pressure

    good news and bad news. the lever on the left is in the locked position that disables the external hydraulics. it won"t move and i don"t know why so i knocked out the roll pin and depressed the shaft going into the valve myself and the remote hydraulics now work. the bad news is i can"t figure...
  5. D

    MF65 no hydrualic pressure

    it"s set up as a single acting. the hose is simply run from the valve by a 3/8" hose to a quick cplr and then on to the cylinder. it"s 2" with an 8" stroak. the hose is attached at the end opposite the shaft and a breither plug on the other end next to the shaft. tha tractor is not at the house...
  6. D

    MF65 no hydrualic pressure

    Forgot to mention the hydrualic/transmission fluid was low and I filled it up before I tried to use the hydrualics for the cylinder.
  7. D

    MF65 no hydrualic pressure

    I have a 1959 MF65 G176 engine. The 3pt hitch works fine. (it lifted round hay bales fine) The remote hydrualics pump fluid but it won"t build any pressure in the cylinder i"m using for the wheeled disc. It will push the rod out on the cylinder when it"s not hooked up to anything but it won"t...
  8. D

    MF65 exhaust manifold torque settings

    thank you. i was seeing about 24-26 as a general rule but it's nice to have the real numbers.
  9. D

    MF65 exhaust manifold torque settings

    I'm going to be replacing the exhaust manifold gasket on my 1959 MF65 G176? tractor. Do you know what the torque settings are?
  10. D

    Hydraulics on MF 65

    <a href="http://s598.photobucket.com/albums/tt62/citybowhunter/?action=view&current=hudraulics.jpg" target="_blank"></a>
  11. D

    Hydraulics on MF 65

    I got it. Now with picture. <a href="http://s598.photobucket.com/albums/tt62/citybowhunter/?action=view¤t=hudraulics.jpg" target="_blank"></a>
  12. D

    Hydraulics on MF 65

    Eric, I can't figure out how to post a picture on this site. I'll send you the picture and maybe you can tell me what type of hydraulic controller is on my tractor. thanks darrin [email protected]
  13. D

    Hydraulics on MF 65

    Here is a picture of the Hydraulic control. the lever on the left shoots out oil in one direction and nothing in the other direction. the lever on the right is fixed and doesn't move or do anything.
  14. D

    Hydraulics on MF 65

    thanks, i'll get a picture of the valve and see if you guys can determine if it's a one way or two way.
  15. D

    Hydraulics on MF 65

    Can someone tell me if the hydraulics on a 1959 MF 65 are one way or two way? I don't know very much about hydraulics so forgive me if i didn't ask the question correctly.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top