(800) 853-2651
SHOP NOW

Recent content by Dave 39B

Yesterday's Tractor Forums
  1. D

    Pics

    Going to try to post a couple of pics.Starting to paint some parts and have others ready to sand blast of my 52 VAC
  2. D

    VAC 3 point

    Thanks guys that's what I needed to know.I noticed that the hyd oil had a milky look to it so I need to drain and flush out before I put it back together. Dave
  3. D

    VAC 3 point

    I was looking through my operators manual and I think it said use 10W oil in my hydrolics.Is this what I should be using or something different. Dave
  4. D

    3 point lift

    Hey C. Amick great stuff I downloaded enough that I might just be able to get by until I can afford a manual.Thanks Dave
  5. D

    3 point lift

    Thanks 1031,I was starting to rethink removing it.I thought it looked heavy.I'll set her off to the side fer a few weeks until I get the main body blasted and painted.I'm sure this isn't the last question I asb before I done.Thanks again Dave
  6. D

    3 point lift

    nothing wrong with it I thought it would make it easier to clean and paint it and the tractor.I've got a cherry picker or should I rethink taking it off. Dave
  7. D

    3 point lift

    Well it looks like I'm going to tear this thing down further than I thought to paint it so I might have a question now and then like I do right now.I have a 52 Csae VAC and I took off the three point arms from the rock shaft(I think that's what it's called) and I got to looking at it and it...
  8. D

    O.T. 79 Dodge 3/4 ton

    I know there's more than tractor knowlege here I've seen it so I thought I'd pick your brains here.I've got a 79 Dodge 3/4 ton 4by4 and I need to chance the rear end but the tags telling me the gear ratio are too rusted.My question is can you get that info from the VIN no. and if not is there...
  9. D

    Case VAC 11,12,or 13

    Thanks Lee,that meens I got the 12 Dave
  10. D

    Case VAC 11,12,or 13

    Don't know exactly what my tractor is.What I do know is that it is a 1952(serial no. 5652704)Case VAC.I was trying to look up some parts and was asked if it was a model VAC11,12 or 13.Can one of you guys tell me how I can find that out.Thanks in advance Dave
  11. D

    Axle seals

    Thanks Lee
  12. D

    Axle seals

    Got another Question for you guys.Does someone know the number of the Axle Seals for the 52 VAC.Thanks Dave
  13. D

    Case VAC

    Hey guys,I just pulled my 52 VAC in the shop to do a few repairs while the snow is flying.I see I"ve got an oil leak between the engine and trans.I"m guessing it"s probably the rear main.My question is does the rear main go in from the rear or do I have to take the rear main cap off and install...
  14. D

    VAC belt pulley

    Thanks Joe thet was it,I saw the set screw but I wasn't sure and I knew one of you guys would know.Thanks again. Dave
  15. D

    VAC belt pulley

    Hi guys,I just got a 52 Case VAC.Today I was playing around with it and when I turn on the PTO the rear shaft works fine but the belt pulley doesn"t work.Is this something simple or am I in for quite a job. Dave
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top