(800) 853-2651
SHOP NOW

Recent content by dave Austin

Yesterday's Tractor Forums
  1. D

    Hydraulic oil or ENGINE oil in a OLD system?

    I repsonded also in the restoration section on this. Its an old 1944 dated ww2 Military clark airborne dozer. My military manual states that it should have SAE 30, or for cooler climates, SAE 20, even SAE10. My question is, I guess, is the hydrualic fluid sold in 5 gallon pails, at auto and...
  2. D

    Hydraulic oil VS. SAE 30 engine oil?

    I refer to the Hydraulic system. My military manual states that it should have SAE 30, or for cooler climates, SAE 20, even SAE10. My question is, I guess, is the hydrualic fluid sold in 5 gallon pails, at auto and tractor stores, something I should consider or avoid? Should I be adding...
  3. D

    Hydraulic oil or ENGINE oil in a OLD system?

    I asked this on the restoration board, thought I might get other opinions here since its a loader specific area of the forum. Ok... recently purchased a older military dozer, (1944 Clark Airborne Dozer) Operators manual states to use a SAE 30 engine oil in the hydraulic system. Really...that...
  4. D

    Hydraulic oil VS. SAE 30 engine oil?

    got a question: It seems that my old crawler (1944 Clark Airborne Dozer) manual states to use a SAE 30 engine oil in the system. Really... Then whats the difference between engine oil and Hydro? I am just wondering, cause what came out MAY NOT be engine oil, it could be something other. Is...
  5. D

    NEED a light like this!!!!

    its not so much the light bucket itself that I am concerned with, its the particular way the mounting is. take a good look: Its got two riveted brackets to the light bucket. They apear robust, cast parts. Between them is a round pivoted stemmed eye bolt to which the threaded portion gets...
  6. D

    SEEKING: A headlight like this!!

    anyone see one of these on any old tractors out there? Its a headlight/spot light as used on a military Clark Crawler, But I would have to make an assumption that it was an item used on other tractors of the ww2 or earlier period. anyone sen on like this on other tractors so I can widen my...
  7. D

    NEED a light like this!!!!

    anyone see one of these on any old tractors out there? Its a headlight/spot light as used on a military Clark Crawler, But I would have to amke an assumption that it was an item used on other tractors of the ww2 or earlier period. anyone sen on like this on other tractors so I can widen my...
  8. D

    Any interest in a GREAT set of Cletrac tracks?

    Thats Milwaukee. and its located about 20 miles west of there. I can be reached at: [email protected] Send me an email.. Ill send some pix to show exactly how nice these parts are!
  9. D

    Clark CA-1 airborne crawlers out there?

    always wanted one. If the right one were to surface at the right price. I might be tempted to buy! Got one? What ya got? Price? Condition?location? please advise
  10. D

    Parts needed for: TerraTrac/ UsTrac/Clark CA-1 crawler?

    looking for the front grill sheet metal piece. Or one that looks similiar.. Anyone know of anyone making repops?
  11. D

    Still looking!!! (Dozer setup for HG42!!)

    yep.. we discussed, CHris. Please send me photos of the units.. What type of blade/unit? Cost? etc. [email protected]
  12. D

    Still looking!!! (Dozer setup for HG42!!)

    Hey LJD.....1200? Yea? Where abouts? Might be worth buying the entire macnine, if its not too far away? Can you send me a link or contact?
  13. D

    Still looking!!! (Dozer setup for HG42!!)

    I still seek a complete unit, one that I can just basically bolt onto my HG42 and put it to work. Factory unit/setup would be best, BUT...Ill consider all at this point. I have been looking for just the blade, simple one or two piston setup. need pump, frame, brackets, blade, everything. I can...
  14. D

    FS: CARCO series SG winch for Cletrac

    This is a complete ready to bolt on Series SG CARCO winch for use on the HG and OC Cletrac crawlers. This is a very rare winch. Very hard to find. These run 100% mechanical, no hydrylics needed. I have the complete setup, including the correct and complete mounting plate as well as the cast...
  15. D

    Small Dozer blade wanted... BLADE ONLY

    now you would think that a smallish blade would be pretty easy to find....not so... looking for ideas and a source for a small dozer blade. Ideally, 5 feet wide at most, 2 feet tall at most, and NOT too heavy! My attempt at using a simple drag type 3 pt blade is working, but I want a little...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top