(800) 853-2651
SHOP NOW

Recent content by DaveBN

Yesterday's Tractor Forums
  1. D

    Rhythmic bumps while moving

    I'd try tightening ALL the lug nuts and bolts. I fixed a Farmall last weekend by doing that. Dave.
  2. D

    Another cub 154 low boy question

    Tip: when I have to cut off a bolt I put a nut on far enough to be out of the way of the cut. Then cut the bolt. Then when you take off the nut it helps to re-form the threads. Dave
  3. D

    SW Michigan Fly Wheelers show 10th-13th

    I am going on Friday. I go every year. Dave
  4. D

    Farmall 140 front mount blade question.

    You'll need to get a manual for the push plow. I believe you use most of the same parts for front mount and belly mount. I believe the plow model will be A and the width demention in inches, as in A 60. Dave
  5. D

    New Avery update

    Another week and it should be running! Dave
  6. D

    Best way to cut lead

    What ever you use spray the cutting area with WD-40. Then the lead won't stick to the cutter as it melts from the heat of being cut. Dave
  7. D

    Oil volume, dipstick or manual?

    Are you sure you have the correct/original dipstick? Dave
  8. D

    Tie rods for Allis Chalmers D14

    The new tie rod ends must be VERY stiff. Maybe try beating them to liquify the grease or drill and tap a jerk fitting and shoot some new or lighter grease in them. Can you weld a washer to the bottom of the old tie rod ends to push the ball up further into the socket and thus take up some of the...
  9. D

    Minnie mo

    I bet it's going to be the Kevin Love model. Dave
  10. D

    Hey Grandpa….

    I am a grandpa but not the one your looking for. I can tell you though that those tanks are hard to clean. There is a baffle at the rear and it is hard to clean behind it. I fill them with water, maybe one quarter full then slosh the water around. Maybe add some ball bearings to act as an...
  11. D

    Farmall C Carburetor

    Did you check the parts section of this site? They show several kits as well as new and rebuilt carbs. Dave
  12. D

    Super C with a Woods L306 Mower PTO Pulley Diameter

    Maybe three pulleys.
  13. D

    Super C with a Woods L306 Mower PTO Pulley Diameter

    In my experience those are always missing, yikes! One could be made fairly easily by a welding shop. It's just a sheet metal cover that wraps around two, I think, pulleys. Dave
  14. D

    IH cub magneto

    Are you testing with the spark plug in the engine or out of the engine? If in the engine is it getting fouled with oil? If out of the engine could be a bad wire or one of the parts you replaced is bad. Dave
  15. D

    6v pos ground amp guage does'nt move when switch is turned on.

    The post on the starter may be worn down after years of use. Take the starter to a good shop and have them put a new post on it. I did this on my C years ago and it made a big difference. Dave
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top