(800) 853-2651
SHOP NOW

Recent content by davek603

Yesterday's Tractor Forums
  1. Goose

    Nibbler.........

    Does anyone else own one of these nibblers? I used this one on an auto body job last April, and I'm still picking "nibbles" out of the soles of the shoes I wear in my shop.
  2. A

    New Holland Hayliner 320 clutch and flywheel

    Hello Gents, a couple of questions. I have a new clutch for my hayliner 320, and I'm just wondering how I set the tension? Should I get new springs too? Also, while taking the clutch off, I noticed the flywheel has a bit of play on the bushing for the input shaft. How much play is...
  3. E

    Trail cutting

    I have a need to cut trails through my acreage. I have used my MF 135 and a bush hog in the past, but I find it hard on the tractor, as well as the bush hog, pushing over the crap with the front end of the tractor. So far I have cut a few km's of trails but want to find a better way so as not to...
  4. N

    4320 and 158 loader project complete!

    Finally have it ready to rock. Thanks for the input on the power beyond block. Works great. Got a kit off eBay for $160 that came with all the fittings and gaskets. My buddy made the bracket holding the valve. Worked out really well. Came across the quick attach reasonable also. Took some...
  5. S

    Purchasing a BCS 850

    Hi everyone, I've just started a small farm - 4 acres, though I'll only be planting one of them for this next year, I need to keep my regular job to stay afloat. I've been looking for walking tractors, and recently came across a BCS 850 with a 14hp diesel motor and a 30" tiller, 32" mower...
  6. M

    Ford 4000 Clicking Noise

    1967 Ford 4000 3 cyl Diesel On 10/24/15 I was working on the anti-freeze flush (another post) letting my tractor run until the thermostat would open and allow the water to flow. I had been doing it for an hour or so, shutting down to drain radiator but did not move the tractor. At the...
  7. A

    3 pt Lift 2400B (454)

    I have a 2400B industrial tractor which is suppose to be the same as a 454 that I have some hydraulic issues with. Whenever I attach a heavy implement like a 1000 lb plow and begin to lift the implement my tractor makes grinding noises similar to when you shift gears at high rpms. After the...
  8. D

    massey ferguson oil pump

    Check with Wengers of Meyerstown Penn. They are a great source of new, used and rebuilt parts. They are very helpful and will UPS to you.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top