Recent content by david nichols

  1. D

    Ford jubilee proofmeter

    I've tried for over an hour going 1/4 turn and trying but it still likes about 3/16" going all the way in. Even had another new cable from same source and tried it...may send it all back and go elsewhere and try again....
  2. D

    Ford jubilee proofmeter

    Yep, I got mine from this site also. The cable housing likes 3/16" from seating on tach. Actually this is my 2nd cable now. I cut one so I would have just the cable to try to see what is going on. It appears that where the cable changes from 4 square sides back to round is the hang up..I cut...
  3. D

    Ford jubilee proofmeter

    Has anyone had problems replacing tachometer and cable in a jubilee ? I know the end of cable is square, and must line up in the square hole in tach. It doesn't seem like it's going in far enough, can barely get the nut started. When I tighten the nut even finger tight the cable will not turn. I...
  4. D

    More Ford jubilee questions...

    Good idea... I'll be double checking that ! Thanks !
  5. D

    More Ford jubilee questions...

    Ok.. finally got rewired, and original thumb switch working, got rid of push button. New problem...the rear hubs had been run loose, like almost falling off loose. I pulled hubs off they were trash, and one axel hub splines were really worn. I ordered one new axel, two hubs, bearings, seals...
  6. D

    Solenoid question

    Going to order correct solenoid...I am thinking the current one is bad / wrong. Push button was hooked from hot junction block to small terminal...
  7. D

    Solenoid question

    I have a jubilee that previous owner disabled the thumb starter switch and put on a push button. I installed new thumb switch, but no go. (Also been switched to 12 volt in past years, with a 172 engine) the solenoid has 2 large terminal, in from battery, out to starter, and one small terminal...
  8. D

    Ford jubilee questions

    I'm trying to get this back to as original as I can but will leave the 172 engine in it. Replacing one axel and both rear hubs, bearings and seals. All new wiring, guages, changing to a vertical exhaust. This will be a working tractor for brush hogging. Going vertical because I set a fire with a...
  9. D

    Ford jubilee questions

    Recently bought a jubilee from a widow, who said her husband had this tractor for over 30 years. The hood emblem just has the stars around it. I finally found the serial number located just back from the starter and according to that it is a 1953 But sometime the engine was changed to a 172...
  10. D

    performance parts

    I just had my 50 8n overhauled in november 08. I bought 4 new 4 ring pistons from newholland tractor. the 8n is alot stronger than before. Now the tires will bog down in 3rd while diskin instead of choking out. My oil pressure runs at 50 psi at 2000 rpms and 20 idleing. All you may need is to...
  11. D

    8n ford 1950 seized motor or bearing

    old, sounds like you've done this before! Thanks!
  12. D

    8n ford 1950 seized motor or bearing

    i was diskin with a 4 ft disk. i checked the oil before i started(20< psi when diskin). while diskin the tractor made a erk noise and suddenly shut off. i have not been able to get it to turn over since. i pulled the starter out and checked it, took the spark plugs out and tried it, and even...
  13. D

    1950 8n seized motor

    trucker40, not too much noise, it was running good and then it suddenly stopped making a erk noise briefly
  14. D

    1950 8n seized motor

    well I tried,, removed the plugs and tried to start it and then I removed the starter (man that was a treat) and it wasn't jammed. I think I have a little job ahead of me
  15. D

    1950 8n seized motor

    thats the one, i tried with a long pry bar
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top