(800) 853-2651
SHOP NOW

Recent content by Defndr

Yesterday's Tractor Forums
  1. D

    Super H clutch

    Thank you CoopertownBob. I appreciate a definite answer on this. I have not had time to go look at the tractor yet. Probably going to pass on this one since I really don't have the space to split one right now. I am glad to find this out before getting it and being forced to do the clutch...
  2. D

    Super H clutch

    Thanks for the replies. I split my Ford 8n to replace the clutch recently. It was my first time doing a split and I was surprised how easy it was after I got the courage up to do it. I really don't have the space right now to do a split on the Farmall so I am glad to hear it probably won't be...
  3. D

    Super H clutch

    I am going to look at a Suoer H that needs a new clutch. It looks like the clutch in a H can be replaced without spliting the tractor. Does anyone know if it can also be replaced in a Super H without spliting? Looks like the clutch is a bit bigger in the Super H.
  4. D

    massey 245 starting problems

    I just had a similar problem on a 245. It would do nothing with the key but I could jump the solenoid with a screwdriver to start it. Turned out to be the neutral safety switch.
  5. D

    8N Governor or Throttle Problem?

    No, the governor doesn't seem to be doing anything. I took the guts including the arms off the old one and put in the new case. It did not work at all. I think the new case is a bit different size, I had a hard time getting the old guts to work in it. I also tried the new governor with the...
  6. D

    8N Governor or Throttle Problem?

    Saw the arms looked a bit different. Seems one was cast a bit off. I tried to grind it but ended up making it worse. I guess I will try to swap the old one into the new case although it looks a bit different also. Oh, those crazy Chinese.
  7. D

    8N Governor or Throttle Problem?

    Thanks, I have adjusted the linkage like that but the set screw will not work to set the high limit since I can't advance the throttle lever beyond one inch, as it reves up too high beond that. The throttle lever must be closer to the full position for it to reach the stop. I think this is a...
  8. D

    8N Governor or Throttle Problem?

    I just tried adjusting the linkage again. No luck. I had tried all combinations earlier. I put the old one on and it worked good. I guess the new governor may be bad. Cheap Chinese garbage we are forced to buy here in American now days! The only problem is that during a 2 minute test the old one...
  9. D

    8N Governor or Throttle Problem?

    Thanks Dell, Yes that is what I'm talking about. I just did not know how to say it so someone not looking at it would know what I ment. I have been looking in the manuals for this thing and the only adjustment I can find is to lengthen the governor linkage rod. That did not help at all. All...
  10. D

    8N Governor or Throttle Problem?

    The thottle lever goes from the idle position (full left stop) to 2200 (it would not stop at 2200 but I stop moving it there) in about one inch of travel to the right (maybe 1/4 of avaliable travel of the throttle lever). It should go to the full right stop and be at 2200 RPM not at be at 2200...
  11. D

    8N Governor or Throttle Problem?

    I put a new governor on my 8N because the old one leaked. I started it and the throttle only needed 1 inch movement to go idle to full power plus. I then put on a brand new carb from Tractor Supply thinking that may be the problem. I runs fine but I only need to move the throttle one inch...
  12. D

    Help reattaching long spring on 8N brakes

    I just did a set and those long springs are a bear. I fought it for awhile then got my brake pliers out. I put the end of the spring on the squiggly end and used it as a pry bar to pull it up and on.
  13. D

    8N Throw out bearing

    Thanks for all the great advice. I will order the cluch kit that comes with a new pilot bearing. Splitting the tractor was a lot less work than I thought it would be but I sure do not want to do it again. I will order a tranny input shaft seal also.
  14. D

    8N Throw out bearing

    Thanks. I have not messed with a clutch in quite awhile but I was thinking the bearing was always a bit loose like this.
  15. D

    8N Throw out bearing

    I split my 8N to replace the ring gear. I was thinking of doing the clutch when I was in there but the disk looks to be fine although I don't know how thick a new one is. I am a bit concerned about the throw out bearing. It spins nice with no noise but it seems a bit loose on the shaft. I can...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top