(800) 853-2651
SHOP NOW

Recent content by DFZ

Yesterday's Tractor Forums
  1. D

    Shaving the head and block for 1940 UTS.

    I am working on my 1940 UTS, and want to give the engine a little more pep. I want to shave the head and possibly the block. How many of you have shaved the block before? It looks like the pistons come about .100" from the top of the block so I was thinking about taking .080" off. Is that...
  2. D

    Tips/Tricks for installing T/A Planetary into overrunning clutch.

    NEVERMIND. I took one more look at it and finally noticed that the planetary is notched so you can remove the sprague clutch from the rear housing when installed together. With the sprague clutch on the planetary you can drop the rollers right in, then re-attach to the rear housing. All went...
  3. D

    Tips/Tricks for installing T/A Planetary into overrunning clutch.

    Anybody have any tips or tricks as to how to install the planetary carrier into the sprague clutch? This is in a farmall 560 and every time it knocks the rollers out of place. Is there a method to hold the rollers back as you install? Thanks.
  4. D

    UTS-D -Special diesel drive question.

    Thanks.
  5. D

    UTS-D -Special diesel drive question.

    The plug is not shown, but is listed under item #8 in the parts list. It is inside shaft #8.
  6. D

    UTS-D -Special diesel drive question.

    No, The plug is inside the hollow drive shaft. The shaft is also drilled allowing pressurized oil from the bushing into the shaft. Where the plug is located determines where the excess oil goes. To the front of timing gear case through the water pump coupling, or diverting the oil to the...
  7. D

    UTS-D -Special diesel drive question.

    I am rebuilding a UTS-D special and we dissasembled the injection pump adapter fully. We knocked out the plug from the hollow injection pump adapter shaft. This is in the adapter housing between timing gear cover and injection pump. The shaft is hollow, and gets oiled from a short line from...
  8. D

    Hot voltage regulator - No charge

    The voltage regulator cross referenced to the same part # as original. Its possible it does not match. Depends how much you trust amazon product descriptions. Identical in size/shape/wire connector.
  9. D

    Hot voltage regulator - No charge

    Im working on my IH 284 with a Hitachi Alternator and a solid state voltage regulator. Electrical is one area where my knowledge is lacking. The tractor was not charging so I replaced the voltage regulator. (inexpensive amazon replacement). It lasted a month and went bad so I replaced it...
  10. D

    Hot voltage regulator - No charge

    Im working on my IH 284 with a Hitachi Alternator and a solid state voltage regulator. Electrical is one area where my knowledge is lacking. The tractor was not charging so I replaced the voltage regulator. (inexpensive amazon replacement). It lasted a month and went bad so I replaced it...
  11. D

    Hydrostatic Power steering problem

    Thanks for the push to test the steering cylinder. It was bad and the piston seal was shot. I would not have thought it could by-pass enough oil fast enough that it would prevent the wheel from coming up to a stop.
  12. D

    Hydrostatic Power steering problem

    We have a Danfoss power steering motor on our FORD 4630 that we have started to have problems with. I post this question here because the same type of hydrostatic power steering system that is used on all brands. The problem is the steering has started to wander and will not hold course...
  13. D

    Cat 2 Implement to Cat 1 Tractor

    A Ford 3600 should be more than capable to handle Cat 2 balls in the lift arms. I would swap out the lift arm balls and use the cat 2 pins on the mower. Given enough time, if you swap the mower to cat 1 pins they will bend. I welded Cat 2 balls into all our ford tractors and we just...
  14. D

    UTS-D Live PTO clutch.

    Thanks. I have only used that style of Live-PTO clutch on an allis-Chalmers before. On those they do snap into and stay in the disengaged position.
  15. D

    UTS-D Live PTO clutch.

    I'm working on a '56 Moline UTS-Diesel. Oil was leaking in the brakes and Live PTO clutch. The Live PTO clutch was seized on and I don't know if it was ever used and definitely had not been used in the last 25 years. I don't think the PTO was ever used on this wheatland tractor. The...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top