Recent content by dg7766

D
Stainless steel prep

I am getting an aftermarket stainless front grill for f40 ferguson [all 3 pieces] and was wondering how to prep it for urethene paint.I don't want it to peel off..rest of tractor has kirker epoxy primer used,will this work on stainless steel as well
- dg7766
- Thread
- Mar 5, 2020
- Replies: 2
- Forum: Paint and Bodywork
D
danuser scrape blade

Thanks for that input,they had everything i needed...
- dg7766
- Post #1
- Jan 16, 2020
- Forum: Implement Alley
D
danuser scrape blade

Was given a danuser scrape,bottom bearing was worn completely out...i can get new bearings and cups..can't come up with a grease seal for it OD would be 4 1/4, ID would be a little under 3"need a grease cap for top as well...any idea's i would be thankful for
- dg7766
- Thread
- Jan 16, 2020
- Replies: 2
- Forum: Implement Alley
D
Z134 engine in TO-35?

Have an engine out of 35 z134...don't have manafold and carb on it..supost to have ben running when tractor was parted out..ended up with alot of used parts when i did my f40...
- dg7766
- Post #1
- Dec 13, 2019
- Forum: Massey-Harris & Massey Ferguson
D
ford 3930

I got block cast # today F0NN 6015 BA and SN *C356597*.......i've got to get a head bolt tomorrow and mic it.sounds like i'm wrong on 1/2 but i need to make sure...thank's a ton for your efforts...9/16 will be lots easier to find
- dg7766
- Post #1
- Dec 3, 2019
- Forum: Ford
D
ford 3930

Thanks for the info
- dg7766
- Post #1
- Dec 2, 2019
- Forum: Ford
D
ford 3930

Tractor is a 1991 model..was bought new...replaced the head gasket to see if that would cure problem..has 1/2 head bolts and takes a 3/4 socket to tighten bolt...can't find a complete engine either..i'll keep trying..thank's for the info
- dg7766
- Post #1
- Dec 1, 2019
- Forum: Ford
D
ford 3930

Middle of NC...been told needed to be from 1990 to 1998..mine has 1/2 head bolts...be great if it would work..mybe somebody here can say if it would
- dg7766
- Post #1
- Nov 30, 2019
- Forum: Ford
D
ford 3930

Found i have block cracked for my oil getting into radiator,no water in oil..have no luck finding a bare block used...everybody says "if" i find one will need to sleeve the 3 cylinders for usually holes come through the walls and put water in the oil..quess this has caused a shortage of good...
- dg7766
- Thread
- Nov 30, 2019
- Replies: 9
- Forum: Ford
D
3930 oil in radiator

Does anybody know the torque for the head bolts,rocker shaft bolts and valve adjustment clearance on 3930 tractor?
- dg7766
- Post #1
- Oct 31, 2019
- Forum: Ford
D
3930 oil in radiator

Thanks for your reply... non turbo so I'll get a head gasket ordered
- dg7766
- Post #1
- Oct 30, 2019
- Forum: Ford
D
3930 oil in radiator

Moved 3930 tractor and had oil coming out front of tractor,cleaned up,1 1/2 qts low on engine oil,oil was coming out radiator over flow.Radiator full of oil..no coolant in oil pan..no oil cooler on tractor...head gasket?
- dg7766
- Thread
- Oct 30, 2019
- Replies: 3
- Forum: Ford
D
MF 150 steering cylinder

Being the cover with the 3 rivits is off,just push the control shaft back and hold it with brass jaws and unscrew the shaft from the link side..the other end needs to come out to replace o ring anyway....how i do it
- dg7766
- Post #1
- Oct 4, 2019
- Forum: Massey-Harris & Massey Ferguson
D
MF 65 gas starter

....................................................................................................................You most likely have one by now....just wanted to add i went through this and got one with same no of teeth...when i tighten it up it would lock up in flywheel...,i had replaced...
- dg7766
- Post #1
- Sep 14, 2019
- Forum: Massey-Harris & Massey Ferguson
D
Carter UT kit

Passing along something postive that happened.I in rebuilding an f-40 tractor had trouble with carb float sticking up and down,which either cut the fuel flow off or flooded.I took it apart several times and read about every fix i could read and tried them ALL with no luck...float itself was...
- dg7766
- Thread
- Aug 9, 2019
- Replies: 0
- Forum: Massey-Harris & Massey Ferguson

Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy