(800) 853-2651
SHOP NOW

Recent content by dkarten

Yesterday's Tractor Forums
  1. D

    MF 65 power adjust rim replacement

    Thx Jim, very useful information , I’ll post after the fire!
  2. D

    MF 65 power adjust rim replacement

    I have soaked adjusters in Kroil & dunked in vinegar but no movement yet, getting ready to heat with Oxy-Acetylene but want to know if I can just reassemble as is? I never have reason to use adjusters. Would I be able to reassemble with frozen adjusters?
  3. D

    MF 65 power adjust rim replacement

    Thx Eric, block of wood worked & wheel center is off , going to clean up clamps & reassemble, might have more questions Both rims are heavily corroded around valve stem from calcium chloride, on this one the valve stem/inner tube connection came apart & I had a flat, before winter I’ll do...
  4. D

    MF 65 power adjust rim replacement

    I have new rim with mounted tire, complete old wheel & tire off tractor , trying to separate hub from rim, all clamps rusted so I have removed all 8 carriage bolts that hold hub to rim & trying to separate & will work on clamps when hub is out of the way, soaked everything with Kroil multiple...
  5. D

    MF 65 Hydraulics

    I removed draft control & there is no fluid coming out of standpipe with engine running
  6. D

    MF 65 Hydraulics

    I replaced the hydraulic pump, all o-rings, the piston rings & all gaskets , filled with fresh hydraulic fluid .Still no hydraulics, I have not yet removed inspection cover to check stand pipe but sure I placed it properly in hole before tightening draft control Considering the debris found...
  7. D

    MF 65 Hydraulics

    Thx, Ive watched the Gingells video but does not answer my question about cause of PTO slowly dropping
  8. D

    MF 65 Hydraulics

    Ive owned my MF65 for 30 years, its a 1960, hydraulics have been mostly trouble free except for 3point hitch slowly dropping, still functional & I was able to work around it In December hydraulics stopped working, I pulled draft control, I have the dual spool, & replaced o-rings on stand pipe...
  9. D

    Massey-Ferguson 65 Hydraulics

    I decided it best to power the splitter with a pto mounted pump, rather than putting a strain on the 65's hydraulics . thanks for all the posts
  10. D

    Massey-Ferguson 65 Hydraulics

    the splitter has the lines & valve on it the manual I have doesn't seem to give info on connecting, let alone the screw, can you give me more info in that?
  11. D

    Massey-Ferguson 65 Hydraulics

    Thanks Eric, I will take pics of both & post them tomorrow
  12. D

    Massey-Ferguson 65 Hydraulics

    I want to avoid having another gas powered engine to maintain, the reason I bought a splitter without an engine & set up for use with hydraulics, this splitter had been hooked up to a skid steer & I thought I could easily connect to my MF65
  13. D

    Massey-Ferguson 65 Hydraulics

    I wasn't aware the pressure would be an issue, the other option I assume is to buy a pump & run it off the PTO?
  14. D

    Massey-Ferguson 65 Hydraulics

    I want to connect a log splitter to my MF65 Hydraulics, it has what I believe is the optional single acting remote control valve, not sure if it is one-spool or two-spool model, there is a right angle fitting that comes off the back, is this for an external hydraulic line? if so where would I...
  15. D

    MF65 Injectiion Pump failure?

    I have what seems to be an IP failure on my Massey, I have fuel at the pump bleeders but nothing to injectors, I had some smoke at first with slight pop while cranking but no start, I have cracked lines & tried to bleed, no fuel, I found a post on this forum by someone else with an MF65 who...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top