(800) 853-2651
SHOP NOW

Recent content by dkattau

Yesterday's Tractor Forums
  1. D

    I'd like a few more RPM on the Allis C I just brought home

    You can put the governor spring and pellet out of a CA in it to gain more RPM.
  2. D

    Plow identification

    It’s a 53. You’ll also need to figure out what series bottoms you have.
  3. D

    Towing an all crop to my home

    If its only 30 miles, grease the hubs before you leave and then again halfway home. I don’t use an offset hitch. If you’ve got any kind of a shoulder, it’ll be okay. I’ve pulled them through roundabouts more than once.
  4. D

    Silly trivia

    The diesel engine was heavier.
  5. D

    Planter Plates

    Any Allis plates?
  6. D

    Allis Sickle mower

    Try it. See how well it works.
  7. D

    Allis Sickle mower

    He’ll need a different hydraulic cylinder. The one on it now is made for 3000+ psi.
  8. D

    AC66 combine question

    The original part # is 523693. Should be a B61 belt, 5/8 x 64 inches.
  9. D

    japanese beetles and dawn dish soap

    Beetles don’t have lungs. Air needs to circulate through holes in their body in order for them to absorb oxygen. The dish soap seals off those holes, and they suffocate.
  10. D

    question about removing a pulley from a shaft

    The pulley and hub are separate. The pulley is what clamps the hub tight to the shaft. Take out the three bolts and run them into the other three threaded holes. That’ll push the pulley of the taper on the hub. The hub and key will slide off the shaft together then.
  11. D

    CA Hydraulics

    You might try using air pressure to blow it out. If that doesn’t work, you may need to just sacrifice the plunger. You can drill a hole in the end and use a slide hammer to pull it out.
  12. D

    CA Hydraulics

    Can you push it into the pump housing against spring pressure?
  13. D

    A bale handle?

    There’s more than one kind of arthritis, and it affects everyone differently. Not everyone is perfect like some of the experts here.
  14. D

    A bale handle?

    You might stop to consider that some folks may have arthritis in their hands.
  15. D

    CA Hydraulics

    They’re not exactly the same. Plungers are the same, but the housings aren’t. Same principle of operation.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top