(800) 853-2651
SHOP NOW

Recent content by Don Loch

Yesterday's Tractor Forums
  1. D

    John Deere H1 Plow

    I think you ask a question on ebay about a plow point I had for sale. Would like to call you. I have to get at least 800 for this H1 plow and it has both types of lift assemblies. I may consider selling hydraulic portion only for 300 which would be easier to ship
  2. D

    John Deere H1 Plow

    I have the plow with both hydraulic and hand lift.
  3. D

    Coulters needed for John Deere H3 and H4 Plow

    Looking for coulters for H3 and H4 two way plows for JD H tractor. Will post a picture. thanks
  4. D

    John Deere H two way plow

    Not yet, think I'll put an add in Green Magazine and Two Cylinder, broaden my search a bit. Check out this link. A JD H with the B2016R weights just below Syracuse, NY. Do you know this fellow? http://www.flickr.com/photos/trumpeterny/5066545826/sizes/l/in/photostream/ JD H with B2016R weights
  5. D

    John Deere H two way plow

    I have both the John Deere H3 and H4 two way plows for John Deere Model H tractors. Need several parts mainly for the H4 plow. Many could be made with the help of a nearby plow owner to allow me to get some measurements. I do need coulter shanks for the H3 and jointers. Is there any one out...
  6. D

    John Deere A Jumping out of 2nd Gear

    I have a 1946 John Deere A which I have replaced the transmission bearings. I also installed new detent springs and balls along with the bearings and can feel a good click when shifting into second. This was done a few years back but the tractor was never pulled hard. I hooked an 812 two bottom...
  7. D

    John Deere H1 plow hand lift lever for model H

    Want to make hand lift lever for John Deere H1 Plow. I am hoping someone who owns one could provide dimensions. I can supply drawings with dimensions blank or if near Toledo Ohio I can measure. Need now overall length dimension of dog links (handle to dog) for work in progress. Thanks
  8. D

    John Deere H1 plow hand lift lever for model H

    Want to make hand lift lever for John Deere H1 Plow. I am hoping someone who owns one could provide dimensions. I can supply drawings with dimensions blank or if near Toledo Ohio I can measure. Need now overall length dimension of dog links (handle to dog) for work in progress. Thanks
  9. D

    Deere 813 plow trip standards

    I've taken one off the plow and carefully removed one of the plates. Made sure all parts remained firmly in other plate. Don't really understand how this assembly works. There are two of the smallest tubular shims, one on each of the half inch bolts. In addition the bottom bolt has a larger shim...
  10. D

    Deere 813 plow trip standards

    Has anyone ever worked on these. Mine were rusted up and wouldn"t move. Noticed the tubular shims sandwiched between the plates and located on two of the 1/2 bolts going thru plates. I think a combination of these shims control pressure to trip. Is there a rebuild procedure when setting these...
  11. D

    813 3 pt plow 12 frame with 14 bottoms

    I'm wondering what model plow mikeinky has. It sounds like it was equipped with 12" moldboards but the throw away 14" share fit? Unless he means a 14" renewable type was bolted up.
  12. D

    813 3 pt plow 12 frame with 14 bottoms

    Would the 12" in GP. style , non thow-a-way ,(sharpen type share) been used on a 800 series plow. Mike do you know type of bottom is on your 12" plow? What model is your plow? At least if the 14" bottoms are right it will eliminate the parts hassle. I'm assuming the 14's are high speed. Thanks...
  13. D

    813 3 pt plow 12 frame with 14 bottoms

    What bottoms should a 813 3 pt plow with a 12" frame be equipped with? This one has 14" high speed. Should a 12" frame be equipped with 12" bottoms? Did John Deere make 12" bottoms?
  14. D

    801 3 pt hitch on John Deere Model B

    So those rods will limit the downward travel of the rockshafts. I wonder if that is true even of the A, 70, 60 and 50. I was concerned about bending something if rockshaft went all the way down with a load. Thanks for the help
  15. D

    801 3 pt hitch on John Deere Model B

    The cranks are on correctly. The push rods that go throught the eyes seem to be to long and will not allow hitch to drop completely when lowered. The cranks on axle brackets that these rods hook to do not seem to allow enough length. If original welds on axle bracket cranks were broke and...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top