(800) 853-2651
SHOP NOW

Recent content by drylakemachine

Yesterday's Tractor Forums
  1. D

    JD model m manure spreaxer

    OK it's in pieces,didn't break anything, Found 1 bearing carrier split ,roller bearing s junk, going have to find them.New shaft with keys So thanks Just need a source for the bearings.
  2. D

    JD model m manure spreaxer

    Wheels will turn backwards ,sprags work axle shaft won't turn Question ,Is any of the pieces on the shaft pinned or should they all slip I'm going to cut the shaft out.,but don't want to break anything Thanks Jim
  3. D

    Adjusting points on John Deere520

    They sell battery with neg on either end
  4. D

    9 n. Steering

    Yes, it's a Kosch, Any value to them?
  5. D

    9 n. Steering

    I have a 9n with a planetary unit under the steering wheel. A mechanical power steering as such. Rare??
  6. R

    John Bennett

    John, Bought some parts from me payment was on time hope he does bussiness with me again sometime,thanks John
  7. D

    Trying to get the 530 running

    Thanks for all the info.Got the ign.parts and it runs,but when I hit the remote cylinder lever,oil bath. Well went and diss.the 3 point and loosened it up .That was because the tube wouldn't come out of it's housing.I mean I could hardly find the quick disconnect,caked on dirt ect. New hoses...
  8. D

    Trying to get the 530 running

    Been here awhile,but just reading.It's been 5-6 years setting, replaced a tube,plus cleaning up the rim.New carb kit,still no start.Rotor was rusted on .so it cracked getting it off.New ign. kit ordered.I noticed looking at the wiring dia.that the bat . terminal on the coil goes to the...
  9. D

    720 D

    Passing my local recycle yard today and some yellow caught my eye.Turns out to be a 720 D.Flat tires,messed up grilled from being scrapped later.Looked ok paint wise. Looked like the pony may have been the problem as the plug wires were off and the top or the carb was unbolted. I was looking for...
  10. D

    Valve Tools

    Just got done pulling two 2n engines apart,first one took 3 days,tulip valves.Broke 2 guides,had to cut off 1 valve,and make a removal tool out of a small welders j type adjustable clamp.I cut a notch in the flat end to fit the valve stem and used a socket on top for the valve to go up into.Also...
  11. D

    now have oil pressure. ? on polarizing generator

    OK after getting the galley plug put in behind the cam gear,it has 45 psi warm. Now the generator,tried jumping across the regulator and nothing on the amp meter,I seen it some where about going direct to the generator but can't find it now.1 wire genny. help Thanks jim
  12. D

    2-N dirty oil,20 minutes max on rebuild.

    Well how about some stupid help forgot to put in the galley plug behind the camshaft gear.(aahh me),Now to put it back together and see what I get. jim
  13. D

    2-N dirty oil,20 minutes max on rebuild.

    This is the one with a busted sleeve.Diss. the block,had the seats ground, hot tanked,pulled a second sleeve.Had the valves ground Installed 2 new sleeves,new valve guides,cleaned all parts and reassembled. OK I knew that most parts were at their upper limit on clearances,but I really thought...
  14. D

    1985 F250 Deisel fuel problems

    Had an 84 with a kind of the same problem,first when you shut it off,have it parked (nose) downhill.Fuel drain out of the injector pump.Next check the water seperator,maybe leaking or sucking air.tank selector may be faulty.I put an inline electric pump on mine,worked good untill the ijection...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top