(800) 853-2651
SHOP NOW

Recent content by dunncl66

Yesterday's Tractor Forums
  1. D

    On Part Number Help - Model A

    Does anyone happen to have the correct PN for the crankcase cover with the starter mount for an early A?
  2. D

    On Part Number Help - Model A

    I currently have a 1937 Unstyled A that I would like to covert to electric start. The current A524R crankcase cover plate is shaped differently then the part I bought A2232R that I hoped would fit.
  3. D

    On Part Number Help - Model A

    Can one of the kind folks here help determine the correct starter mounting plate part number for an early Model A please. I was told PN A2232R would work but it is not shaped correctly to cover the case. The A2232R has a clipped corner and is different than the non-electric start A524R cover...
  4. D

    Unstyled A with Increased Compression

    Does anyone have a well tuned tractor that won’t hand start and you have to pull it off? I am sure I can improve the tune of this one some but it would be encouraging to know it will work once it’s perfect.
  5. D

    Deere Magneto to Distributor Question

    Got a 3 ohm coil to cut out the resistor, all is good now. I now now all about ignitions coils, thanks all.
  6. D

    Deere Magneto to Distributor Question

    Coil has 1.2 ohms across it so I am guessing a resistor is needed to get to the 3 ohms
  7. D

    Deere Magneto to Distributor Question

    The coil skin temp is painful to touch so I am guessing it’s 150 degrees give or take after 5 mins of run time. I did not perform any work on the tractor yet as I just got it. I will do the ohm meter work - thanks for the advise.
  8. D

    Deere Magneto to Distributor Question

    When a magnetor is swap with a distributor and a coil is a ballast resistor required? I have a 50 with a distributor and the coil is getting pretty hot when it runs and I am wondering if I need a resistor like a car.
  9. D

    Unstyled A with Increased Compression

    Thanks for all the feedback.
  10. D

    Unstyled A with Increased Compression

    I have a number of old green iron. The petcocks are indeed open. The pistons passing them in the stoke makes sense. After reading a little it sounds like pulling tractor mods of this type result in a pull starts only tractor.
  11. D

    Unstyled A with Increased Compression

    Help. I bought a nice Unstyled A with increased compression - something about plated pistons and domed valves. It has so much compression that I cannot pull it through the compression stroke to hand start it. It pull starts ok but I would like to be able to hand start it. Is there anything...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top