(800) 853-2651
SHOP NOW

Recent content by dzus

Yesterday's Tractor Forums
  1. D

    1 inch fitting on pump leaking ford 2000 3 cyl

    Our 2000 is doing the same thing. I talked to an old Ford mechanic and he said Ford had a fix for that. Instead of using a new "crunch" nut they cut a little off of the line and flared it. Then they used a different fitting in the pump and a different nut on the line. He said this was right from...
  2. D

    Oliver Super 88 engine ser# location

    Thank you. Yes this one has key start & vertical stacked lines so I will go with the late one. Still can't find a ser# on the engine block anywhere.
  3. D

    Oliver Super 88 engine ser# location

    #2 injector line. My book shows 3 different part #'s. Early eng ser# used 1KS1703A. Middle range used# 1KS1703B. Latest one was #101022AS. Of course my book is for 88 & Super 88 and Oliver is not nice enough to let me know when the switch was. Do these all sub up or are they different?
  4. D

    Oliver Super 88 engine ser# location

    I have a Super 88 diesel I need to find the engine serial# for some injection parts. Where is this number located? The book shows a 7 digit number. Is that correct? Thanks
  5. D

    Ford 3-cylinder gas block

    I am wanting to over haul a 2000 3-cylinder gas engine. I have a bunch of spare parts engines. I have 3 different engine blocks. All 3 have different casting numbers. C5NE6015A, C9NN6015A, D0NN6015J. These should all be gas blocks with 4.2" bore. I assume each one is newer that the...
    • dzus
    • Thread
    • Replies: 1
    • Forum: Ford
  6. D

    White 2-78 4-78

    White 2-78 & 4-78 what were they? Were they all forklifts or were they wheel tractors also?
  7. D

    Need a part number please! PTO shield.

    I ran this on the Ford discussion forum yesterday and somebody identified this shield as a Ford Major shield. Can somebody supply me a part# for this? I can't find a picture of this in my parts book? Will this work on standard and raised PTO or which one is this for? Any help greatly appreciated!
  8. D

    Can you identify PTO shield

    Got this on a pallet of misc Ford stuff. Approximately 9" long from front to back. Can anybody identify what it fits?
    • dzus
    • Thread
    • Replies: 3
    • Forum: Ford
  9. D

    Allis 5020. Need engine or parts

    I have a customer that needs a used or rebuilt engine or a used or rebuilt short block for one of these little rolling junkpiles. 2 cylinder Toyosha diesel engine. Does anybody deal with these things at all?
  10. D

    Roosamaster pumps myth or fact

    Back in the day I went to a local tech college for diesel mechanics. We had a special clean room for working on injection pumps. It had its own air filtering system and all the special tool and testers etc. We were all warned escpecially about Roosamaster pumps how critical cleanliness was. All...
  11. D

    Ford 3000 rear axle

    I am wanting to put a rear axle seal in a 3000 that has the axle bearings retained by the big self locking nut. My I-T manual says Nuday made a tool to remove and replace this nut. Does anybody still make a tool to do this? Chance of finding a used one? Homemade options? Book says retorque to...
    • dzus
    • Thread
    • Replies: 2
    • Forum: Ford
  12. D

    3-cylinder hydraulic pump identify

    I want to buy a used pump for a 3-cylinder Ford 3000. The one that bolts on top of the clutch housing. My parts book show 4 different pumps. #C5NN600AA (3000 early), #C7NN600Y (3000 late), C5NN600AB (2000 early), #C7NN600Z (2000 late). Is there any way I can identify a pump like this without...
    • dzus
    • Thread
    • Replies: 5
    • Forum: Ford
  13. D

    90 series updates

    The problem will be you can't tell by looking if it's been done or not. Unless you have some paper work from previous owner or dealer don't bet on it being done.
  14. D

    power steering 202

    Are you talking about the lines going to the cylinder? They are pressure hoses. Too much pressure for a hose clamp type splice. They are a tight bend where they attach to cylinder. I doubt if a hose shop could duplicate exactly. We bought new ones from Agco a couple of years ago. They were...
  15. D

    MF 230 hydraulic pump identify

    I have a MF 230 tractor ser# 9A267961. I am going go through the hydraulic belly pump. Is there a sure fire way I can identify which pump I have? Is the part# of pump stamped on the pump somewhere? I am in Agco online parts books. There is 6 pages of hydraulic pumps and that is just in the early...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top