(800) 853-2651
SHOP NOW

Recent content by Ed Oliveira

Yesterday's Tractor Forums
  1. kcm.MN

    2020.06.24 Tractor Pic

    puzzle: https://jigex.com/GWaM
  2. D

    Ford 1720 4wd

    My 2001 1720 won't stay in 4 wd--If you pull on the rod to engage it will disengage after a short move--if you pull up hard it may stay engaged but then grinds--stays in better in reverse than forward- is this something that can be fixed from topside or does the tractor have to be split...
  3. K

    Honda motor

    I have a Honda one cylinder motor in a side by side utility vehicle that is getting gas in with the oil and could use some help finding out how it is getting there. I am thinking I have carb. problems? Can anyone help. It is a 390cc side shaft low hours.
  4. C

    Fall Work this week here

    Been a Very Un-Normal year here it seems,, my field work started the 4th of February and is still going now as you can see, a few shots for you from the past week, I installed a set-back on the north field gates the one pic with the drawing was done by my good friend Doug Nelson who does...
  5. T

    Starting problems STX30

    Would really appreciate some help with my STX 30. Will turn over some of the time, but usually requires that I spin the flywheel by hand to help it get going, or move it to a different position. Have replaced starter because it was doing the exact same thing with the old starter. I can hear...
  6. C

    ANOTHER snow day...

    Third day in a row school buses have not run.Lots of lake effect snow today with wind,some roads still closed from yesterdays blast. I think I'll have another coffee. Ben
  7. B

    Charlynn Power Steering Question.

    What should I run in the system for oil? We were going to put power steering fluid in it, but after further inspection, it looks more like 15-30 would be appropriate?! What do you guys think?? Has the pump mounted on the Gov housing on a Farmall M, and the resivor is directly above it inside...
  8. G

    TSX 597 Marvel Schebler Carb Nozzle Assembly Removal

    Well, it looks as though the above VAC-14 carburetor must come off the tractor for nozzle assembly removal/cleaning. (see post below). I just hope I find something wrong inside that will cause it to idle properly. Usually these simple old carburetors are pretty forgiving. Glenn F.
  9. N

    Unstyled JD A Governor Issues!

    I took the throttle rod of the carb when running. I manually moved the butterfly to the open position to see what the governor did. It did really nothing. So I don't think it's the spring. Inside the governor, everything looks fine, free, and like it dhould work like it's suppose to with the...
  10. F

    Randy in Oklahoma call me Matt

    Randy sorry to try and reach you here. Unfortunately, my phone got wet and will not let me retrieve my contact list or any of my text msg's. I picked your car up Tuesday and look forward to meeting you on the 29th. Matt
  11. F

    Governor Spring TO-30

    No one seems to carry governor springs. They have compensation springs but not the one that attaches to the governor lever. I found one locally that is about the same length with a couple of more coils. Will that work? What is everyone else using? I haven't bought the one I found yet. I wanted...
  12. D

    4010 turbo post

    In the 4010 turbo post below, I noticed no one but me mentioned overheating when turbo kitting 4010's and 4020's. Back in the day when it was the popular thing to do, around here the topic of how to keep the 4010-4020 kitted tractors from overheating was a common coffee shop subject. What are...
  13. I

    806 rims - only 4 bumps??

    I had to get new tires on my '63 International 806. Now that the new tires are on the rims, and the rims and hubs are painted, I am confused about how to mount them. Specifically, the rims have two ridges (for mounting at different extensions) and each ridge has only 4 "bumps", rather than all...
  14. 1

    Resto-ride seat question

    I am restoring a resto-ride seat for my 960. I am to the point of ordering bushings. My question is: What keeps the front bushing on the seat arm/base from coming out during use? I see no way of retaining it once it is in place. Can anyone shed light on this or maybe I am missing something...
  15. G

    8N hydraulic oil

    I used CARQUEST 80W 90 gear oil GL-5 in my 8N but it seems to foam a little. Did I use the wrong oil. thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top