Recent content by edinmo

  1. E

    630 Rhythmic growl cause and question.

    I'll lead off with my question: can the pto sliding drive gear be replaced with just 1st gear reduction area access? I'm considering replacing the PTO crankshaft drive gear, idler gear and sliding drive gear. The noise is there with the sliding gear disengaged so it's mostly in the crankshaft...
  2. E

    630 rhythmic growl

    It has independent engine driven PTO. PTO drive gear on the crankshaft and idler pulley run anytime the engine is running..
  3. E

    630 rhythmic growl

    Thanks. Got the clutch totally off, put the driver disk back on, covered the fork assy mtg hole, ran the tractor and the growling is still there. I hate to be dogmatic about anything on these old tractors but right now I'm convinced the source is somewhere in the 1st reduction housing. The only...
  4. E

    630 rhythmic growl

    I'll work on that. Of course that movement is basically at the outer end of the crank. So the actual movement at the bushing, which I'm guessing is 10-12 inches from the end of the crank would be proportionally less than .017. I'm just not sure that level of movement would cause the growl I'm...
  5. E

    630 rhythmic growl

    Thanks for the input. The driver is very tight, no spline damage at all. Do you know of any suppliers of good main bushings other than Deere.
  6. E

    630 rhythmic growl

    But with the clutch tightly engaged causing the clutch pulley to be tightly bound to the drive disk, wouldn't that eliminate all pulley movement resulting from pulley bushing or bearing wear? I'm not sure, I'm just trying to logically work my through to what I should do next.
  7. E

    630 rhythmic growl

    Using a pry bar and dial indicator, I can engage the clutch and move the clutch up .017". Since the clutch is engaged the crankshaft moves with it. Would that much main bearing movement create that much noise? Any inputs on how to proceed in replacing the main bushing, source, cost, precautions...
  8. E

    630 rhythmic growl

    I agree. The noise volume inreases and decreases regularly and the frequency depends upon engine RPM. Sounds like something wobbling agains a shield or something oblong rubbing against something.
  9. E

    630 rhythmic growl

    I'll try moving the crank when I get the pulley off. I considered the crank main but I don't know why that wouldn't be a constant noise. Hope it doesn't move. It'll be a couple weeks before I can get into it that far but I'll post back. Thanks for the inputs and comments.
  10. E

    630 rhythmic growl

    My plan is to take the clutch pulley completely off, put the clutch driver disk back on, start the engine and see if it goes away. Any problems with doing that?
  11. E

    630 rhythmic growl

    Seems like it has to be in the clutch or something in the 1st gear reduction gearing. Engine main noise would be constant I think.
  12. E

    630 rhythmic growl

    You're right I need to get into it. I'd like to work the tractor for an hour or so to see if anything else may need work. Would that be too risky with the possible clutch problems?
  13. E

    630 rhythmic growl

    Here's a short clip. The clutch grabs and is jerky. I can lift on the clutch pulley and watch it move up and down. Is the clutch bearing bad, needs lubrication, or both? I just opened this file and no sound. When I tried to upload the video I kept getting file too large messages. Sorry.
  14. E

    630 rhythmic growl

    Yes, that rhythmic growl is always there.
  15. E

    630 rhythmic growl

    Doesn't go away when the PTO is disengaged. It's there when in neutral with clutch engaged or disengaged. I'll work on posting a video.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top