(800) 853-2651
SHOP NOW

Recent content by ElectricMan

Yesterday's Tractor Forums
  1. E

    Crankshaft size

    Thanks
  2. E

    Crankshaft size

    What is the standard size for the rod bearings on a 841D with 172cc engine
  3. E

    841D Rod Bearing

    Thanks Guys all the responses were really good. RickB's offer is good so I'll contact him. Blessings
  4. E

    841D Rod Bearing

    I had a noise on start up after I removed the oil pan I found #4 piston rod cap loose. the lock nuts was missing and I could remove the cap nuts with my fingers. Upon closer look after the rod cap was off i found #4 crank throw very rough. My question is the most effective way to resurface the...
  5. B

    Oats are under snow

    Well good old pa weather sunny one week and 75 and 30 thus morning and inch of snow hope my oats will be ok suppose to be sunny and in the 50 this weekend
  6. E

    ID Parts

    Thanks $ Bill I will get photo's and search for more #'s. Those were easiest to find.
  7. E

    ID Parts

    I have the following I would like help on to which model these are: Rear end # F792. Transmission # SH 7000 F2, Axel 8N 4012 A2, Arm # 8N54. These are for swap or sale.
  8. E

    172 Diesel injectors

    old brake adjusting tool works for me
  9. E

    stuck steering wheel.

    Here is my system---PB Blaster first with several app's then got good 1/2 inch rope wraped the spokes as close to the hub as I could get making each rope leg same length positioned my coe along over the wheel at the same angle as the column. hook the rope loops, tighten the comea long loosen the...
  10. E

    821 Tractor

    Thanks Guys---going back tomorrow and get serious as to what it has and get an asking price. I know i will have more questions.
  11. E

    821 Tractor

    Hey guys I found a 821 this one has power steering, 3-point and PTO. Serial # 48**** can't recall all the numbers. has good tin,aftermarket seat, tires 1/2 tread. Just wondering on price range.
  12. E

    My $1200 Ford 2000 gas

    Very nice
  13. E

    How can I drop the amps on my 12 volt jump box?

    Al take 2 asprin go to bed it will be better tomorrow.
  14. E

    Drive Shaft

    Thanks this is good info. I will keep your # I will call soon
  15. E

    Drive Shaft

    How do I figure out the length for a shaft from a 841D to bush hog? What is average cost? Does anyone have one for sale? What color should it be? Thanks Doug
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top