(800) 853-2651
SHOP NOW

Recent content by Elliotturner

Yesterday's Tractor Forums
  1. E

    Bamford Super 58 baler - How tight should the plunger be?

    Hi, I am hoping to be baling in 3-4 days and I’m trying to sort my baler. If is a bamford super 58 It’s just had new plunger bearings It had sat outside so I had to remove runners in bale chamber and clean out behind them All clean now and going back together but I don’t know what point to...
  2. E

    Hydraulic linkage bent slightly

    Hi, I was assembling the hydraulics on my ferguson TEF20 yesterday and once the top cover was all on and I went to connect the control valve, I realised something wasn’t right. The linkage has bent slightly which I believe is from over tightening the draft control knuckle It seems to work fine...
  3. E

    Primer isn’t adhering

    I bought a new line, cleaned the compressor thoroughly and had a filter before the line and after. I am positive that nothing is coming through the air stream now and the primer went on ok, there were a few fisheyes in the first coat but the second coat covered them up. I have had a few runs and...
  4. E

    Primer isn’t adhering

    Tried it today and primer went on ok, much better than before but still not perfect
  5. E

    Primer isn’t adhering

    Upon going back into the spray booth again today, I noticed that on the piece of cardboard that I tested on, it had the fisheyes aswell So hopefully I have solved the problem of oil in the air I’ll report back tommorow after I have painted
  6. E

    Primer isn’t adhering

    will isopropyl alcohol clean the parts well enough? I have found out that the compressor was overfilled with oil by about 3x what it should be. I have put the correct amount in now and cleaned up the tank and lines etc. I have a new airline, filter on each end. I used isopropyl alcohol to clean...
  7. E

    Primer isn’t adhering

    Used a wire wheel on an angle grinder to get paint and rust off
  8. E

    Primer isn’t adhering

    Hi, I have attempted to paint some parts from my ferguson TEF20 engine today and the primer wasn’t adhering. i am using a high quality epoxy primer and a good quality gun with a 1.8mm nozzle. My air compressor is old and I have quite a thin airline.which Means the max psi I can get before the...
  9. E

    David Brown 1490 weight?

    On a trailer No extra weight 2wd Cab Loader Bucket
  10. E

    David Brown 1490 weight?

    Hi, I’m looking at buying a David brown1490 (with a cab, loader and bucket) and hopefully I would tow it back behind a pickup with a 3.5 ton towing capacity I am in the UK. Does anyone know what the tractor weighs and a rough guess of the weight of the loader? I have found specs on tractor data...
  11. E

    Castle nuts on big ends- over torque or under torque to line up cotter pin?

    Would it make a considerable difference to balance By adding a washer or filing a nut down? At the end of the day it’s a 73 year old engine which will have an easy life not a performance engine from a race car?
  12. E

    Castle nuts on big ends- over torque or under torque to line up cotter pin?

    i torqued the nuts to 65 ft/lbs the bottom of the range, then turned them until the slots lined up some went at 70ft/lbs . others had to go to 95 ft/lbs. Mechanical draper torque wrench which is nearly new
  13. E

    Castle nuts on big ends- over torque or under torque to line up cotter pin?

    In the 5ft/lb range, some of them don’t get close to lining up
  14. E

    Castle nuts on big ends- over torque or under torque to line up cotter pin?

    Yes
  15. E

    Castle nuts on big ends- over torque or under torque to line up cotter pin?

    Bottom of the conrods with the end caps that go onto crankshaft
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top