Recent content by Eric Benton

  1. E

    John Deere loader very slow to raise

    You may have a loader with a open center hydraulic valve on it. Some of them have a plug you can put an oring on and change it to a closed center valve. The easy way to check this is to crank up the tractor and just let it run for 15-20 minutes and then put your hand on the loader control valve...
  2. E

    Liberty Tractor Pull

    I have had that happen before also, and decided it was not worth the 3 hour drive (one way)to pull, The AC 190XT crossed the line on the left at 50 ft and crossed the line at 100 ft on the right and was not disqualified. It was stated very plainly at the drivers meeting that anyone crossing the...
  3. E

    Liberty Tractor Pull

    Wow!! I am going to take that as a complement! I enjoy good competition that forces me to be on my game.
  4. E

    IH 484 burns my eyes-strong fuel smelling exhaust

    That should be a D179 3 cylinder IH engine not a Perkins if it is a 484 IH.
  5. E

    Rich Hill, SC Fall Festival Pull Saturday

    Larry, What time will the pull start? Thanks, Eric
  6. E

    farmall cam timing

    The camshaft gear has 58 teeth which should be 6.2 degrees per tooth. You can safely move 1 tooth in either direction and the tractor will crank and run. I have never been able to find ready made offset keys for a Farmall M. I always have to go to the machine shop and have them cut me a key. I...
  7. E

    tractor is ready

    Did it run good with them magic popping pistons?
  8. E

    715 combine carb kit

    That should be the right kit. A lot of IH parts numbers are 1 digit off of the cast number and the 534932R91 does not come up in the parts book but the 534933R91 does show in the parts book. I will bw glad to build your carb if you want me to. I don't know how to price it untill I open it up and...
  9. E

    460 puller

    JD Plowboy, The flywheel step should measure 1.188 inches.If it is more than this it will not clamp as tight as it should. If it is s little less it will clamp tighter but the fingers will be closer to the release bearing.
  10. E

    New engine

    Might need to order a new clutch and find a longer hood!! Eric
  11. E

    3020 dangerous power steering

    It is not a toe in problem and the toe in should be between 1/4 and 3/8 of and inch. More than likely the orings on the end of the steering pistons have gone bad. This is in the steering motor at the front of the tractor. They can be replaced without pulling the steering motor housing out of the...
  12. E

    FORTS POND ANTIQUE TRACTOR PULL, PELION SC

    It was my first experience with National rules.And to judge by how the finishes were in each class I would say the different divisions did a good job dividing up the tractors to keep them competitive. I have pulled at alot of different tracks and by lots of different rules and for the most part...
  13. E

    John Deere tractorpulling

    We had one on the farm years ago that we bought used from the local JD dealer. He dyno"ed it for us and it was turning 375 HP. We had it turned down to 275 HP and used it for years for our heavy tillage work. The guy who had it before us turned everything up just as much as it would stand.
  14. E

    JD 4020 Fuel Sender

    I don't know where the term came from. I have it heard it called a piggin wire since the mid 60's. I think JD calls it a fusible link.
  15. E

    JD 4020 Fuel Sender

    The JD 4020 diesel early model is not a positive or negative system. The Electrical system consists of a 24V cranking system, 2 seperate 12V charging systems,(one per battery), 2 seperate 12v light systems(one per fender) and the polarity of the light changes from one fender to the other fender...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top