(800) 853-2651
SHOP NOW

Recent content by Farmall-H

Yesterday's Tractor Forums
  1. F

    Farmall an and hitachi alternator help

    Hey guys, I have mounted a remanned hitachi 13421 alternator on my h. The previous alternator was a one wire alternator and I am wondering if that is all I will need for the new one? Or is there any other wires i may need to run? I am also wondering if someone could tell me where to run the...
  2. F

    Throttle pedal on Super A

    I am sorry, I did make a mistake, it is a 1949. It does have a diamond shaped front axle which also threw me off seeing that I have never seen one like that before. Sorry for the mix up, -Cole
  3. F

    Throttle pedal on Super A

    Hey guys, I recently squired an 1939 super a and I have one question. This tractor has an extra pedal near the brakes which to my surprise turned out to be a throttle pedal. Was this an aftermarket add on or was it factory? I have never seen anything like it before! Thank you for any input...
  4. F

    Many tractors

    I will be up in St. Cloud the 15th-17th for the mn fruit and vegetable growers convention at the river center. Great times and meet a lot of tractor guys. I farm south of the river in Apple valley rosemount area. -Cole
  5. F

    Farmall a transmission oil help!

    I overfilled my transmission on my A by one quart, plus I added 1 quart to the belt pulley. It has both a pto and belt pulley. Would it be wise to drain some out via the oil level plug on the left side of the transmission? Or will it be fine overfilled by a couple quarts at most? Thanks guys!
  6. F

    Wiring for farmall A

    Hey guys, What gauge wire is used for the kill switch to ground out the magneto on my A. Or which gauge do you recommend? Thanks as always! -Cole
  7. F

    IH 285 Planter

    I just so happen to be the guy you bought it from, and it"s not that I don"t care, it"s that I mis-spoke. It is a 295 planter unit and since I used it very little the unit number was not fresh in my mind. It did not say it on the planter but I did my research from who I bought it from and it...
  8. F

    706 steering wheel kicking my butt!

    My steering wheel is the spitting image as the one below. The only thing is, it looks like they beat the heck out of the Hub with a hammer it is completely dented. I'm afraid that squeezed the hub tighter on the shaft. I will try heat and time with my 3 jaw puller -Cole
  9. F

    706 steering wheel kicking my butt!

    I am pulling from behind the hup. It's a small puller. Would you happen to have a picture or schematics on how to make the puller you described?
  10. F

    706 steering wheel kicking my butt!

    Can you not just pull from the center puller hole on the steering wheel shaft? I have a the three way puller and put it behind the center of the shaft and placed the puller on top of the threaded portion.
  11. F

    706 steering wheel kicking my butt!

    Hey guys, I cannot after weeks of penetrating lube, get the steering wheel off of my 706. The cap is long since gone and the nut that holds the steering wheel on is gone as well. I assume and am convinced its rusted beyond my original thoughts. Any advice on a very stubborn steering wheel? My...
  12. F

    706 steering wheel

    Can anyone tell ,me how exactly to take the steering wheel off of my 706? The cap is long since gone and all I see is about one inch of threads and a hole in the center which leads me to believe you use a puller? But if the steering wheel has 36 spindles than why Are the threads there? Thanks a...
  13. F

    12 hole weight bracket bolt size for mounting?

    I have a 12 hole weight bracket for my 706. I am not near the tractor till this weekend and I am wondering what size bolts are required to fasten the bracket to the tractor? Thanks In advance! -cole
  14. F

    706 hydraulic filter red flag!

    Hey guys, when replacing the hy-tran in my 706 today, I noticed something that raised a flag for me. When I pulled the hydraulic filter, the relief screen was full of tiny metal flakes. I believe it amounted to less than and teaspoon. The filter had not been replaced for some time, and the oil...
  15. F

    Finished plowing today!

    Got done plowing the sweet corn ground today...4 days of plowing, new shares and a tired driver. He he he The 7120 and the 735 vari-width, a great combo. -Cole
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top