(800) 853-2651
SHOP NOW

Recent content by FarmallCT

Yesterday's Tractor Forums
  1. F

    IHC No.10 Sickle Bar Mower for F-20

    That would be great, I have attached a few pictures below for you to compare. The first two pictures below are of the one missing the sickle bar, the next two pictures are of the complete one further away with what I believe is the correct bar. Thanks in advance, ~FarmallCT
  2. F

    IHC No.10 Sickle Bar Mower for F-20

    That would be great, I have attached a few pictures below for you to compare. The first two pictures below are of the one missing the sickle bar, the next two pictures are of the complete one further away with what I believe is the correct bar. Thanks in advance, ~FarmallCT
  3. F

    IHC No.10 Sickle Bar Mower for F-20

    Hi All, I am looking at a couple of No.10 Sickle Bar Mowers which were made to mount on the Farmall Regular and F-20. There is one near me with the mounting brackets, but that is missing the cutting bar. I have found another complete mower, minus the mounting brackets, about 8 hours away. I...
  4. F

    International Harvester Electrall Information

    Thank you, I did do a quick search and found quite a bit. I will be sure to go through these and see what I can find. ~FarmallCT
  5. F

    International Harvester Electrall Information

    Thank you for the information. Do you have any idea where parts could be found for this unit? Particularly electrical parts? Can modern electrical parts of the same function be used? Being built in partnership with GE, are there any other GE products that use the same electrical setup? I am not...
  6. F

    International Harvester Electrall Information

    Hi All, I am trying to find out more information about IH Electrall generators. I recently saw a PTO version for sale and would like to learn more about them. I have heard about these before but have never seen one in person. From what I can find they certainly do not appear to be very common...
  7. F

    Ford 9N Sleeve Installation

    We are working on getting it setup to heat the entire block to a higher temperature with what we have available to get a greater difference in temperature.
  8. F

    Ford 9N Sleeve Installation

    Working on getting dry ice. The place nearby is closed for the rest of the week and the others nearby are too far away to be able to pick up during the day.
  9. F

    Ford 9N Sleeve Installation

    It was briefly considered but due to time and budget limitations was not something that could be done. It was not anticipated that the sleeve installation would be as difficult as it has been.
  10. F

    Ford 9N Sleeve Installation

    We were able to get a hot air blower from the small animal lab to use to heat the block, gets it up to a very nice temperature. We are working on getting dry ice and will also likely hone the block out a bit more as the head holds the sleeves in a bit and they should expand when running.
  11. F

    Ford 9N Sleeve Installation

    These new sleeves seem to be more prone to cracking and shattering more than collapsing. The old sleeves we pulled out were definitely more durable and bendy. Have not been able to find an installation tool yet, trying to get some dry ice currently.
  12. F

    Ford 9N Sleeve Installation

    Any idea where a driver can be obtained? Have looked online but cannot seem to find one and when we do it does not appear to be the right size. Other problem is if we do find it the supplier needs to be setup as a vendor with the school and accept purchase orders. We will definitely try cold...
  13. F

    Ford 9N Sleeve Installation

    The school is located in central Connecticut. Thank you I just might.
  14. F

    Ford 9N Sleeve Installation

    Hi All, As mentioned previously I am working on a Ford 9N project with the mechanics class I am teaching. We have reached the point at which we are ready to begin to install the sleeves and reassemble the motor. This tractor takes .040 thin wall sleeves and we are trying to avoid breaking...
  15. F

    Ag Mechanics Class Ford 9N Engine Rebuild - Update

    That may be true, although I would not expect a lip to be that significant, especially on a dry sleeve engine, and on .040 sleeves it is supposed to be only a slight flare at the top. The other measurement I am using to come to the conclusion of .090 sleeves is that according to the linked...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top