(800) 853-2651
SHOP NOW

Recent content by farmerboy9400

Yesterday's Tractor Forums
  1. F

    john deere 567 round baler

    I agree with u. I make single rows and butt them together and only a inch or so gets spoiled. Works for me but I would like to store them inside some day.
  2. F

    john deere 567 round baler

    Ok thanks.
  3. F

    john deere 567 round baler

    Thanks guy. Yes I am talking about the rubber feed rollers. On my 535 I had to use the talc lube from jd to prevent that from happening. About the roll spacer I am going to use up my 64 inch net roll before buying a wider one so where can I get the spacers from and do I need them on all rolls?
  4. F

    john deere 567 round baler

    Just bought a 06 John deere 567 baler with net wrap and mega wide pickup and was wounder if the 567 still has the problem of the net wraping around the rubber roller like the jd 535? Any help and tip that you may have on the 567 would be nice.
  5. F

    john deere 535 round baler belts slipping

    ok, I just bought one of those cds and will see what I can find out. hope fully I can fix this problem. Thanks so much for your help
  6. F

    john deere 535 round baler belts slipping

    ok, thanks for all your help. I might end up taking baler to dealer and tell them to check all of the hydrolic components on baler. Thanks again for all the answers.
  7. F

    john deere 535 round baler belts slipping

    What could you find out with knowing what size the core is when gage reads as set? Also so far what do u think my problem/problems could be with this baler?
  8. F

    john deere 535 round baler belts slipping

    Thanks again, I conected baler to our JD 8110 and JD 5420 tractors and on both when I closed the gate and let go of scv lever, the gage read at 10 0clock and after 5 minutes it was reading at 9 oclock. should I keep tractor valve in float position while baling?
  9. F

    john deere 535 round baler belts slipping

    No I have not tried baling with a different tractor, and the tractor I am running this baler with is a JD 8110. I cleaned the adjustable valve with solovent and compress air already, and one JD service person I talked to about cylinders told me to warm the tractor oil and run the hydrolics on...
  10. F

    john deere 535 round baler belts slipping

    yes im sure belts are routed correctly, they are just like the manual tell me and the JD service guy also checked them. When should gage move to preset psi? Like i said im not sure, it could be closer to 3'. wish I could go bale some hay to tell you for sure. Is it possable for the density box...
  11. F

    john deere 535 round baler belts slipping

    not sure I would say around 4' and I only make 5'x 5' bales. should the density gage read the same with big windrows and smaller ones? yes i have had them out twice already. when we got baler 3 years ago the belts were loose and slipping. I did tests on hydrolics the best I could without the...
  12. F

    john deere 535 round baler belts slipping

    tension bar cylinder do not pull in all the way they are about 1" out from crome shift, but there are some stops on top of baler that seem to hold it from coming down further. Also i am baling mostly ditches and there are big and small windrows mixed together so the bale dinseny warries, and...
  13. F

    john deere 535 round baler belts slipping

    I have a 1991 jd 535 baler and the belts are slipping. could anybody help me with this. we had a jd service guy here and he cheaked barings nd looked baler over and told us to shorten belts which are now 10" shorter that the min in book. I also put some 3m traction tape on drive rollers. It...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top