-
F
Ford 4600 stabilizer bar installation help.
That was my assumption too. Maybe I should just get a smaller bolt and large washers to make the existing bolt hole work where the lower arm and lift arm connect.- flyfisher23
- Post #10
- Forum: Ford
-
F
Ford 4600 stabilizer bar installation help.
This is the kit I bought https://www.ebay.com/itm/326188353045 It says "250C, 260C, 2810, 2910, 3230, 335, 3430, 3550, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 420, 4400, 4500, 4600, 4610, 4630, 4830, 5030, 515, 532, 535 // Replaces Part Numbers: D9NNB856B-RHKIT"- flyfisher23
- Post #8
- Forum: Ford
-
F
Ford 4600 stabilizer bar installation help.
Interesting... Good to know I, in theory, shouldn't have to drill a hole. The shoulder bolt for where it attaches to the link/lift arm is way too big to fit in the hole, and to replace that existing bolt where the lift arm attaches to the lower bar... :/ I am not sure what to do next. My...- flyfisher23
- Post #6
- Forum: Ford
-
F
Ford 4600su electrical - wires on top of transmission that go no where
You all are great. Thanks for the thoughtful replies. This is good to know, starting the tractor while not in the seat and by the tire has always seemed like an easy way to get hurt, and I admit to doing it - luckily i've checked that its in neutral every time. I will check it out and the...- flyfisher23
- Post #7
- Forum: Ford
-
F
Ford 4600su electrical - wires on top of transmission that go no where
These wires go nowhere on my new tractor. The lights worked when I got it, but now a 5-amp fuse is blown. Probably irrelevant to this, as I'm sure the wires are brittle and shorted to the tractor frame somewhere. What do these 2 wires attached to the transmission area go to? Seems like a...- flyfisher23
- Thread
- Replies: 6
- Forum: Ford
-
F
Ford 4600 stabilizer bar installation help.
best way to install this 3 point stabilizer bar? It seems like I need to drill a pretty big hole in the lift arm to run the shoulder bold thru. Whats the best tool and way to do this? Any tips so I don't screw it up? How far out wide on the axle can I install the drop down bracket- flyfisher23
- Thread
- Replies: 11
- Forum: Ford
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy