(800) 853-2651
SHOP NOW

Recent content by Fred Hart

Yesterday's Tractor Forums
  1. F

    Pumpkin planting - am I going about this right???

    got this info off another site: Deere has plate number B27436 for pumpkins. This plate must be used with filler number Y2630B with cutoff spring number Y5064B. Contrary to what the eBay sellers would like you to believe, this plate can still be bought new from Deere for less than $40. I've...
  2. F

    TO-35 Tappet Noise Gas Model

    1957 TO-35 Gas Ferguson Tractor Z134 engine The tractor runs good and idles at 400 rpm's. The other day i noticed a tappet noise at high speed when i was plowing. At idle there is no tappet noise. Have a loud upright muffler on tractor, so it is hard to tell motor noise. I run shell rotella...
  3. F

    Advice

    In your price range: if you are looking at a MF maybe a 165-175 model diesel, but if you do buy one of these _______(be sure)_____ it does not have multipower. get a 4 speed with high/low trans only!!!!!!!!!!!! this M/P option was nice when new, but these tractor are 40 years old and any...
  4. F

    Dirt Scoop - use stabilizer bars or not?

    TO-35 Ferguson tractor and Ford dirt scoop if i am pulling forward i normally do not use the stabilizer bars. but if i am having to back into the dirt pile, i do use the stabilizers as it is hard on the lift arms and chains.
  5. F

    Voltage Regulator Tuning / Adjustment?

    i have had my to-35 for many years. its a 12 volts but the same system. i finally gave up on the adjustable voltage reg and just bought a new one. get the best one you can buy, many are made overseas and are cheap if you want to adjust it, be sure the battery is up to charge, around 6.5 to 7...
  6. F

    Tractor Shed - Wood Bees

    Help! Wood bees are trying to eat up my tractor shed. they are boring holes in the roof joist. can i mix up some posion in a bucket of water and set it out in the shed. Would this work??? mix some posion with water in a bucket, hang it up in the barn, maybe the bees would drink it then...
  7. F

    Ford Rear mounted loader

    goggle a dearborn 19-29 rear mount loader. should fine a good picture of the loader
  8. F

    plow coulter setting

    MF Poor, Do you have a picture of your plow with cover boards (aka trash boards) or any information on where I can buy them for my MF 62 plow Thanks,
  9. F

    plow coulter setting

    thanks for the input, I have tried taking off the coulters, but it did not help, maybe some, but the vines and filth just choked up around the plow beams. Thats why i tried the new coulter blades. I do most of my truck patch plowing in the fall, when you have the most ground cover filth, try...
  10. F

    plow coulter setting

    This old set of MF62 plows makes a better trash drag than plow. So I replace the coulter blades and set them at 6" off the ground. I can pull the plows at around 7" deep with my TO-35 Fergy. I seems the trash builds up in front of the coulter frames then plugs up the plow, as more trash...
  11. F

    ferguson to 35

    might be good money spent to take it to a machine shop and have them press it off if you do not have a good setup. if you bust the pulley you just add to your expense. pulleys can be ruined pressing them on to the new pump. take you time
  12. F

    135 out of gas, carb leak, and white smoke.

    when my old TO-35 does this, leaks gas out of carb because float is not stopping gas flow, I cut fuel off at tank, then pull air inlet hose off and let any excess fuel drain out. You do not want to pull that raw gas into cylinders if it can be helped. But when the tractor starts, its normally...
  13. F

    Cultipacker Questions

    i guess when new the rollers were touching, but old cultipackers can take a lot of abuse and still get the job done. nothing will make seed come up any better than using sometype of old cultipacker. they are getting harder to find and much more expensive, i got mine years ago for $50 and it...
  14. F

    MF 62 plow coulters

    he is a small local eq dealer he had the slotted blades 16" for $20 each. I will have to drill out some of the holes as the new ones only have 3 holes. I will get one of the old ones apart before i buy the new blades.
  15. F

    MF 62 plow coulters

    he is a small local eq dealer he had the slotted blades 16" for $20 each. I will have to drill out some of the holes as the new ones only have 3 holes. I will get one of the old ones apart before i buy the new blades.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top