(800) 853-2651
SHOP NOW

Recent content by fullpull88

Yesterday's Tractor Forums
  1. F

    Same mini Taurus 60 hydraulic

    I have a same mini Taurus 60 4x4 and I love it. But I can't find an oil filter for the remote hydraulic system. Anyone know a number? Tom
  2. F

    970 with mw turbo

    Im working on bending the nail over on this deal. Its a white one
  3. F

    970 with mw turbo

    I have an opportunity to buy a 970 turbo it has a pyrometer on it good tires and runs excellent. But the ptp has problems. He says it stoped last summer and ge says he turned the pto backwards and it works again but has a tick. That to me means it lost a tooth. He wants 2500 bucks it aint real...
  4. F

    Oliver 1465

    Update on the 1465. Filter housing was replaced with one from a 5050 Allis. Filter is 22 bucks at napa. The starter is a gear reduction job for a 7.3 ford motor but not the powerstroke. Had to shim it out 1/4" also the register is not 90mm but smaller going to get a bushing made for that but the...
  5. F

    Oliver 1465 in junk yard

    I need the nose cone. The patina is just right to match mine.Where in Wisconsin? I'm in Curtiss but id drive a little. Big Sal
  6. F

    Oliver 1465

    Thanks but I will not spend 115 dollars for an air filter. I will change out the housing for something else.
  7. F

    Oliver 1465

    Thanks
  8. F

    Oliver 1465

    Yes I know its an orphan. I bought it cheap runs good and good rubber. What it doesn't have is a air filter, i opened the can and there wasn't a thing in there except dead mice and the final filter. I cant find any listing for a filter. Can you guyes help? Big Sal gentleman farmer.
  9. F

    1450 cub repower

    Where did the picture go?
  10. F

    1450 cub repower

    1450 had a motor knock and the old honda deck was bad so here ya go.
  11. F

    1250 cub cadet spindle bearings

    Why are spindle bearings so expensive? Cheapest I found is a&I 94 bucks or so. Anyone have a better priced suppliers? Big Sal
  12. F

    Dettson snowblower

    I'm blowing with an 830 Case and the auger shear pin shears allot. It seems like the one plate has a hole for the bolt and the other has a slot. And the plates are an 1/8" apart. None of that seems right to me but it's a used blower and I got no paperwork. Looking for answers.Big Sal
  13. F

    830 Turbo

    Thanks Mel looks like I have time to install the turbo now,lots of rain in central Wis. Big Sal
  14. F

    830 Turbo

    Do you have any pictures of the oil lines on the turbo? I'm wondering where to dump the oil back in. Thanks Big Sal
  15. F

    United farm tools

    I found a cheap plow in excellent shape today. Four 16 semi mount it says united farm tools on it. Can you still get shares for this and was it a good plow? Big Sal.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top