(800) 853-2651
SHOP NOW

Recent content by G BRAGG

Yesterday's Tractor Forums
  1. K

    Super C Ia to Mn 1985

    My neighbor near Iowa Falls, Ia had a nice Super C that had been painted like a 350. It was sold to someone in Minnesota in 1985. Also had a 2 row cult. Does that ring any bells? I'm not looking to buy, just wondering as I have some of his other machinery. Thanks!!
  2. A

    McKee roundbaler

    I have a friend who is looking for a manual for a McKee roundbaler.Is there anyone out there that knows of one. Thanks
  3. G

    3 point hydraulic lift jack WHAT IS IT

    OK ***I LIKE IT DO YOU HAVE A PICTURE OF THE FRONT JACK HA HA I JUST WISH I WOULD HAVE THOUGH OF THIS THANKS FOR THIS POST GLEN IN WASHINGTON
  4. G

    Ford tractor

    Roger I am sure these ole boys here will add to this but try this link it will help ya and get you started .have a good one Glen http://home.att.net/~jmsmith45/identify.htm may have to copy and paste
  5. G

    OT well pressure

    Hi Tex we could go in to this step by step but take a look at this link it may help ya and answer some questions,and i also agree with the others ,check the pressure switch first and tank pressure,I have worked on a few ,not to hard . good luck Glen from washington...
  6. G

    ot, aahh dell, tell me it isnt so

    Thank you I am new here but totaley agree Glen
  7. G

    1 post

    "now thats funny I don't care who ya are" (LARRY THE CABLE GUY) GLEN
  8. G

    thanks pull behind

    Well I never expected so much responce on this topic,I just want to say I read ALL of the comments and taking your advice,and ideas my bucks will be to get a trailer to move my 2N around to help my neighbors again thanks the brush hog lives on.(or another N ) HAPPY NEW YEARS TO YOU AND YOURS...
  9. G

    PULL BEHIND

    Gary thanks for the words of wisdom,Iam not realey mad at any one,and you are right the DR is in the neighborhood of $2500.00 and around here that would get me another N and bucks for a trailer and of corse when my bride reads this post well I know I will have to buy her something HA HA. Glen
  10. G

    PULL BEHIND

    kirk the one Iam looking at dose have a adjustable off set if I do pick it up I will try it on my N and let ya all know how it works,your idea of both at the same time ,I just had a vision HA HA what a site this will make and again it may work. thanks Glen
  11. G

    PULL BEHIND

    WELL DEN FIRST OFF I AM NOT STUPID AND THIS N IS A TOOL AND IF IT CAN BE USED OTHER WAYS THEN WHY NOT,I ASK FOR HELP THAT IS ALL NO OTHER REPLY NEEDED GLEN
  12. G

    PULL BEHIND

    yes I have a good lawn tractor that I agree may be the way to use this ,havent bought it yet ,but the hog is waiting to get dirty,I will have to think about the pull behind ,as it is a good chunk of change thanks Glen
  13. G

    PULL BEHIND

    ok let me throw this at ya,what do you think of a DR pull behind brush cutter with the 17 hp motor and a 44" cut I want to pull it behind my 2N ( dont need to use the pto),I also have a brush hog with one hour on it befor the tractor quit ,but with your help it is running great and waiting for...
  14. G

    Rookie question

    Hey Ken just got back from the "club" what a neet place also, I found a wiring diagram that is the best ,it showed me a wire that must have burned off the resistor at the gone bottom lug wellll time to go back to the barn Thanks again Glen from Wash
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top