Recent content by Garri

  1. G

    John Deere 4020 lp hard to start

    When I jump the starter with the screwdriver, it engages every time without any clicking. All connections are fresh and clean. The starter was bought new last year. I purchased it as new, not rebuilt. I took the battery to Interstate today and they load tested it. It tested fine.
  2. G

    John Deere 4020 lp hard to start

    I need a little help and information on a 4020 lp please. The tractor has always been kept under a shed and last year I replaced the starter, alternator, battery, neutral safety switch and recently replaced the push button ignition switch and key switch. The battery connections are not corroded...
  3. G

    D19 LP will not start unless pulled

    That is a good question. I don't know. I will ask NAPA tomorrow. The coil came from there. Maybe the computer or book will tell.
  4. G

    D19 LP will not start unless pulled

    Thanks for all the info. The condenser and points that are in there now are the third new set that I have put in in recent months. Same old story with all three sets. I guess it is possible to have three bad ones in a row, but I'm thinking it is something else. Danged if I know though. I...
  5. G

    D19 LP will not start unless pulled

    The resistor was removed years ago and not there. One thing I forgot to mention is when I have the distributor cap, rotor and cover off, I only see spark at the points intermittently. When there is spark, it is weak. Only every now and then I get a good bright spark in the points. I have not ran...
  6. G

    D19 LP will not start unless pulled

    We have a 1962 Allis D19 factory LP that has become very stubborn. I have replaced ALL of the following: Alternator, points and condenser (twice), spark plugs, spark plug wires, coil, distributor cap, battery and rotor. Starter seemed to be dragging a little, so I just had it rebuilt. I also...
  7. G

    4020 LP died won't start

    I forgot to add that it does have a new neutral safety switch installed. Everything is good there. I found out today that the starter is dead. Will not spin or engage on the tractor even when shorting it across. I took it off and hooked up a set of jumper cables and still nothing. Just a...
  8. G

    4020 LP died won't start

    I am working on an early JD 4020 LP. Just before this problem, tractor received new 12v battery, spark plugs, wires, distributor cap and alternator. It has an electronic ignition so I didn't install the points & condenser. I also cleaned the oil bath air filter and put in new Mystik 30 weight...
  9. G

    IN NEED OF John Deere 555 rear wheel

    What I need is the small 12x4 rim that used the rubber tire. A blank rim won't do me any good due to the fact I don't have a center to weld in. The mounting flange and everything else is there, just not the rim - wheel.
  10. G

    IN NEED OF John Deere 555 rear wheel

    I am in need of the rear wheel for my John Deere 555 drag plow. Does anyone have one for sale or know where I can get one? I would greatly appreciate any help. I need it rather quick. Does anyone know the bolt hole spacing? The best I could tell it is 4 on 4 1/2. Thanks.
  11. G

    urethane paint

    Has anyone used Ag Specialty paint sold by All States Ag Parts?
  12. G

    urethane paint

    If you guys don't mind, fill me in on what urethane paint is. The best I can recall, the man I got the paint from said it was urethane. I really don't remember though. What I do remember is I did not have to add hardener and I only added about 4 ounces of the clear liquid he gave me in the pop...
  13. G

    urethane paint

    I painted one of our Allis Chalmers tractors a few years ago with what I think was urethane paint. The man I got the paint from got it from his supplier, but wouldn't tell me who the supplier was or who made the paint. The paint can was just plain silver with no labels. He gave me a soda bottle...
  14. G

    Massey 65 Carburetor TSX695

    The hole where the throttle shaft goes in is wore and very sloppy. A screw has been twisted off where the butterfly attaches to the throttle shaft. When I tried getting the broken screw out, I drilled out part of the screw and made an oblong hole in the throttle shaft. It has apparently been...
  15. G

    Massey 65 Carburetor TSX695

    I may be looking for a needle in a haystack, but I am needing a good and complete carburetor for a 65 gas. My old carb is a Marvel Schebler TSX 695. It is too wore out. If anyone has one, please let me know how much. I'm trying to avoid buying a brand new one. Thanks in advance.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top