(800) 853-2651
SHOP NOW

Recent content by Garycw

Yesterday's Tractor Forums
  1. G

    buying used tires and rims

    With the new sizing from 12-28 how would 13.6-28 and 14.9-28 compare? I have a 841 & 851 with these two sizes. I thins one says 12" rim & one says 13" rim?
  2. G

    801/851 starter switch- neutral safety hook up?

    I'll check that out. If I can figure out how to do it without buying another solenoid would be great.
  3. G

    3pt hitch quit lifting

    I'm not familiar with that tractor, but I assume you checked fluid level and if it looked clean and not milky?
  4. G

    water in hydraulic fluid

    What helped me get rid of the dreaded milky fluid was drain several hours, 40/40 mix K1 & UTF and 20% ATF & isphoryl alcohol. Run 30 min & let sit over night. Run some more then let drain a few hours. Change any filters,open any bleeders, crank to get any left out of pump. I then...
  5. G

    hydraulic pump priming

    ??? I don't understand the logic of jacking up the back of tractor??? What's that have to do with hydraulics and makes for a potentially dangerous scenario.
  6. G

    801/851 starter switch- neutral safety hook up?

    Thanks cbrown. It looks like solenoid has been changed or something. It's not original to tractor and is hanging behind air cleaner( not mounted). I'll get a closer look to see how it's grounded and look at a oem one.
  7. G

    hydraulic pump priming

    Here's a good vid on priming http://youtu.be/qkv0MfmFupw
  8. G

    3 Point Hydralics

    I just got one that did not work at all. Mostly water, milky oil mess. Sitting two yrs outside. I drained middle hydraulic resivior,put back in almost a gallon UTF ford spec 134d fluid, gallon of kerosene, pint alcohol , & quart of ATF. Ran it for about 30 min, working lift lever and after...
  9. G

    hydraulic pump priming

    No jacking up needed. Fill redivide with 2 gal of UTF with 134D spec for ford. Lossen bleed plug on pump( without motor running) wait and see if fluid appears. Yes- re install plug , start and work lift. No- reinstall plug, remove dip stick and with rubber tip air gun apply about 5 lbs air...
  10. G

    801/851 starter switch- neutral safety hook up?

    Recently got a 851 that key switch added with start position. This eliminates the neutral safety start button. How do I Hooke this back up and replace if needed?? The 841 wire going to button is common to ground/ chassis
    • Garycw
    • Thread
    • Replies: 4
    • Forum: Ford
  11. G

    801 12v conversion wiring problems

    if everythings hooked up correctly and working properly and the tractor running,I should be able to remove the negitive battery terminal and the tractor should stay running..correct?
  12. G

    801 12v conversion wiring problems

    The diode can have heat shrink or electrical tape. The load side of switch is the side going through ballast resister to coil
  13. G

    801 12v conversion wiring problems

    When I take this shortcut from alternator to coil, I would run through resistor first, correct?
  14. G

    801 12v conversion wiring problems

    Thanks old, I will probly do that for now since the toggle switch being used for key is very hard to reach. I tried to take back of dash off for access and got all bolts out except for the two top screws. I will work on later and put new wiring harness and key switch when I take the hood off to...
  15. G

    801 12v conversion wiring problems

    Yes, I found that the hard way after backing bushhog into barn and swarmed by yellow jackets. Trying to make a hasty escape the tractor wouldn"t shut off. Had to use the choke to shut down. I was going to use a diode and a light both.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top