(800) 853-2651
SHOP NOW

Recent content by gbs

Yesterday's Tractor Forums
  1. G

    mf 4710 harsh clutch engagement

    grandson recently bought a used mf 4710, it has an issue with the clutch engagement being harsh intermitently for no apparent reason, one dealer updated the software and recalibrated it, worked for a day or two, another dealer replaced a linkage on the clutch pedal, in a day or so same...
  2. G

    cat 3116 engine mui governor

    thanks for your reply, i pulled it back apart and turned the sleeve washer combo on the spool around that is held in place by the little snap ring and it fired right up. that was my fault it appeared to be assembled in the wrong direction.
  3. G

    cat 3116 engine mui governor

    governor won't move the rack to the on fuel position, it has oil pressure to it, fuel solenoid is working and the rack isn't stuck, also the small e-clip has been replaced that breaks on the control spool inside the governor housing, what did i miss
  4. G

    601 work master hydraulics

    thanks for the replies, I finally got a chance to remove the tube and sure enough it had a hole in it, from the appearance of the tube I wonder if electrolysis caused the hole as there wasn't any rust on it except some small etching next to the where the hole was eroded thru?
    • gbs
    • Post #7
    • Forum: Ford
  5. G

    601 work master hydraulics

    How can the hyd fluid be pumped into the transmission? The tractor in question shortly after start up will start oozing hyd oil out around the shift levers.
    • gbs
    • Thread
    • Replies: 6
    • Forum: Ford
  6. G

    2000 hyd strainer

    how do you remove the hyd suction strainer on a 2000
    • gbs
    • Thread
    • Replies: 4
    • Forum: Ford
  7. G

    carb has me stumped - Farmall BN

    i had a chip of paint above the needle valve seat do the same thing
  8. G

    End of an era

    we have both types of mower conditioners, for speed the disc mower is faster, but if your crop is laying down the reel and sickle bar will give far better results, couldn't convince the grandson about the difference until both were used in the same field that had a lot of it laying down the...
  9. G

    electrical question

    even though several electricians have explained to me i can't seem to understand the purpose of the green bonding screw being used or not in a single phase 220 volt electrical panel box when followed by a sub panel. i know it's suppose to connect the neutral and equipment grd bars to the panel...
  10. G

    Super M Pilot Bearing.

    if you can get a pneumatic impact hammer to it you should be able drive it off, if not and you're comfortable using a cutting torch remove the rollers and trim the race off the shaft, also a die grinder with a cut off wheel works well, cut the race on opposite sides avoiding hitting the shaft...
  11. G

    Trailer wheel seals

    if you have the seals that the sealing surfaces are inside the seal itself one of two things happened, they didn't fit the spindle correctly, or what most of the time happens is when installing them a small dent is made to the housing of the seal and they will leak for sure.
  12. G

    measure and set differential backlash ?

    you can lessen the noise by using unless straight 140wt gear oil instead of multi-viscosity type unless you are in a cold climate. also be careful as some of the gear oils may not be the wt claimed, I remember Daddy filling up the old m farmall with 140wt Sinclair brand and it poured like thick...
  13. G

    What is antifreeze snuff?

    i could write a lengthy page on the myths of antifreeze that i have found not to have any merit, your most accurate means of determining the level of protection you have is a good tester. years ago me and a coworker were making sure the trucks on the yard had enough antifreeze in them and the...
  14. G

    TO35 clutch help

    were there any installation blocks or pins holding the pressure plate in the released position if so were they removed, if not the adjustments are wrong and the pressure plate is bottoming out. if they were removed and the height adjustment is correct the new springs used could require more...
  15. G

    150-174 tranny swap???

    all depends what you will be using it for, it most likely will as far as the transmission it should be the same depending on the gear set-up, depending on the tire size the rear end gear ratio's may not match, and I doubt the drive axles can stand the hp unless the 150 had the planetary drives...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top