(800) 853-2651
SHOP NOW

Recent content by Gene Sage

Yesterday's Tractor Forums
  1. G

    Throttle lever

    When I Google Tomure nothing comes up.
  2. G

    Throttle lever

    Where can I find the throttle lever for a 66 series that has a 90* bend In it like tractor pullers use?
  3. G

    Paint code

    I need the paint code for the off white on 66 series tractors. I have the red from this site, but can?t find the off white.
  4. G

    Wheel luhs

    The differential has needle bearings, the transmission has different gears and the clutch is a triple disk 11". I've tried to address the weak components.
  5. G

    Wheel luhs

    So which is it 90 or 180? It's on a 666 with a DT 466 so I need to have it right!
  6. G

    Wheel luhs

    What's their purpose?
  7. G

    Wheel luhs

    On 66 series tractors there are 2 lugs attaching the wheel to the rim that are slightly different. What is their purpose and where are they to be positioned?
  8. G

    Paint codes

    What's the paint codes for the 66 series red and off white. Will be using base, clear coat paints.
  9. G

    Right hand step

    In process of restoring a 666D and looking for a right hand step for 666 or 686.
  10. G

    4960 digital tach

    I have a '94 4960 with a nonworking digital tach. It has the electronic injection pump. It's my understanding there are two speed sensors. One picking up speed from the front of the engine on the cam. The other being a speed sensor in the injection pump. I replaced the speed sensor on front...
  11. G

    Exhaust elbow

    Working with Ed Leaman parts. He is supplying triple disk clutch, TA eliminator shaft, front and rear adapter plates. Not sure about the need for needle bearings in differential. Won't be a serious sanctioned puller, just a few county fairs etc and tractor rides. Probably start with a 11 or 13...
  12. G

    Exhaust elbow

    It flows to the middle. The intake side of the turbo is to the rear and and makes a sharp bend to the airfilter. Compressed air from the turbo makes a bend to the front flowing to the intake manifold. How much horsepower will the transmission stand along with the final drive?
  13. G

    Exhaust elbow

    Installing a DT 467 engine from a 5288 in a 666. Will the exhaust elbow from a 1066 or 1466 fit on the base and provide a vertical exhaust?
  14. G

    Administration

    Larry made an error?
  15. G

    Engine transplant.

    About to begin the process of installing a DT 466 in a 666D. Will be changing the front and rear covers to adapt to the narrow frame, lengthening the frame, installing a triple disk clutch, and doing a TA delete. What do I need to do in the area of the transmission and final drives to withstand...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top