(800) 853-2651
SHOP NOW

Recent content by GG1170

Yesterday's Tractor Forums
  1. G

    1070 Hydraulic issues (Non powershift)

    A while back I posted some questions pertaining to hydraulic issues on my 1070, no power steering, 3pt not raising, & very slow remote cylinder lift. However, if I cracked the smaller fitting on the pump I will see air bubbles then suddenly fluid starts pouring out so I re-tighten the fitting &...
  2. G

    3020 pto won't engage

    Thanks...the pin #15 came out per no cotter pin. Thank you again!
  3. G

    3020 pto won't engage

    I have a 3020 with powershift transmission that the pto constantly spins. We've dealt with this for years, anyhow it stops when a load is applied but now the lever that engages the pto moves freely & has no detent. I don't feel engagement. Is there a linkage under the cowl that came disconected...
  4. G

    Best older JD for 3 point snow blowing

    Don't know where you are located but we will be putting our 3020 gas on auction in April of 2017. Dad used it for blowing snow & it worked good with a 6ft Farm King blower behind it. I'll be happy if we get 6k for the combo. The tractor is a '64 with powershift & we never had issues with the...
  5. G

    4430 vs 4440

    Can anyone tell me the advantages Deere improved the 4440 over the 4430? I usually see nice 4430's priced about 10k less than a 4440 in they're respective age & shape. As a kid I loved the appearance of the Sound Guard JD 30 series & I've always dreamnt of owning one someday. What were any...
  6. G

    AGCO Allis 2025

    It was a pretty clean break. However, one thing I forgot to mention that may be very crucial is prior to the original belt breaking my wife hit a log chain & wrapped it up & killed the motor so my guess the deck is wasted. From the alignment checks I made I couldn't see any major misalignment...
  7. G

    AGCO Allis 2025

    Pulleys spin free...bearings were removed & inspected before this last belt was installed.
  8. G

    AGCO Allis 2025

    What a shame. I got an Agco Allis 2025 that has a 60" Simpliciity mower deck on it & the problem isn't the tractor. I can't keep a belt on the deck to save my *%$#. The tractor has 375 hrs on it & the original deck belt lasted about 250 hrs then it blew. Ok, not bad...bought another, this...
    • GG1170
    • Thread
    • Replies: 9
    • Forum: Agco
  9. G

    hydraulic oil filter relief valves

    Well I'm stunned by the price of these hydraulic oil filter relief valves when you discover you need one. $400 from CIH & $150 from Agparts. From what I see they are made similar to a thermostat. I'm in the wrong business. Sure enough, my 1070 needed one as someone failed to replace it upon...
  10. G

    Jean Claude Marleau - Great to Work With

    This message is a reply to an archived post by jmandrze on March 09, 2016 at 07:53:40. The original subject was "Jean Claude Marleau Great to Work With". I just received a relief valve for my Case 1070 hydraulic oil filter. It got here before I even got a check off. This is a great guy to...
  11. G

    power steering issues again

    I pulled pump off & found o-ring was rolled up sideways some & kinked. I was so happy to see a problem that I re-installed the o-ring on the inlet tube & put together & started tractor with no power steering still until I cracked the upper small line on pump & took a oil bath. The oil came out...
  12. G

    power steering issues again

    So this means taking the pump off the back, some disassembly & replace the seal? From the parts book it does look like an easy fix. Thanks John. I may also give you a call. You helped me with my front end bearings & seals. Thanks again
  13. G

    power steering issues again

    Went to use my 1070, after sitting about 2 weeks, the power steering don't work. I started it up only to move it to make room in my shed but now can't even do that...Any suggestions what to look for? I was in the process of changing the hydraulic filter but I can't get the nut loose from the...
  14. G

    Vermeer 605G Round Baler

    Yes...I crowd the best I can but today the bales looked much nicer. I'm putting up short grass hay & the windrows are wider today because of a better stand of grass. One thing I have to watch is my belts track off if I'm filling to much on right side vs left so I concentrate more on the...
  15. G

    Vermeer 605G Round Baler

    My baler is making what I consider a loose bale. Is there any adjustments I can do to make a tighter bale? The belts are wore too. Would replacing them be the answer? Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top