Recent content by ginger underwood

  1. J

    MW hand clutch

    This message is a reply to an archived post by kevinj54 on August 01, 2013 at 13:54:30. The original subject was Re: MW hand clutch. I need some parts how do I get in touch with Kevinj54
  2. L

    WTB: John Deere Front Steel

    Looking for a set front of steel wheels for a B John Deere. If more than one set is availble I would like a set for my model A as well.
  3. Tom in TN

    Adding pump oil to a floor jack

    I have two floor jacks. One relatively new one and one that is about 20 years old. My old jack was not lifting well, so I decided to add some hydraulic pump oil to it to see if it would pump up properly. I don't know what brand it is, the old label is long gone from the jack. I found a...
  4. C

    MF202 3PT Lift problems

    I went to use my 202 this morning. Started fine. I always turn the lift lever off when I park this thing so PTO is not activated when I go to start the tractor. I put the PTO in gear to raise the box blade off the ground and it raised fine. I then tried to put the PTO in neutral as I...
  5. M

    MAJORMAN

    Hi Brian, will you be going to the Marsham Rally this weekend? I will be going to do the commentry for them and I will be taking my wifes 1962 Dexta that I restored for her last year. MJ
  6. Klyde

    MW circa 1962

    After the discussion below thought I'd put this up.
  7. D

    UB seat shock absorber

    My UB needs a new shock absorber which is located within the seat spring. Can anyone point me in the right direction as far a a part. number. Thanks
  8. big tee

    Consignment Sale--

    Went to a sale 40 mi South of me yesterday. Lots of small stuff and a few rows of tired big stuff. I bought a big load--a fire plug--yard art!---Tee Case 1175--$2600 IH 460--$1300 Loader for 460--$200 Deere 7100 bean planter $1300--bought right! Case 580c--$8550 HS--spreader--Hauled...
  9. J

    Gravely Model with a ser# J7122

    All, This is only tag I find. It is on the differental/trans. What year and model is correct for this? Thanks Jim
  10. O

    Ran when parked.........

    Here's a project for one of you guys, only missing a few parts...... Mpls Craig's list this morning Case Car Chassis
  11. F

    Black gunk seeping down 188 engine block

    This is on a 431 diesel. At first I thought it was oil from the head gasket or valve cover. Further investigation, it seem to be coming out the exhaust. It?s a black oily substance. Pictures attached. Thanks Jim <image src="http://forums.yesterdaystractors.com/photos/mvphoto13290.jpg"/> <image...
  12. B

    replacing a gas 148 with a 159 diesel in Case 300 series?

    Need to replace a late 1950's G148 in a Case 310B with a 159 cu in diesel out of a late 1950's Case 300 series. Is this possible and how feasible? Any insight will be greatly appreciated! Thank-you!
  13. P

    John Deere 4000 Hydraulic Issue

    Was using my 4000 to mow hay last weekend and when I went to pick the haybine up at the end of the field, I had no hydraulics. I still had good steering and good brakes. I took the tractor to my shop. Pulled the transmission screen it was clean. Replaced the hydraulic filter still no...
  14. F

    Massey 35 Drawbar

    Have a 35 Massey. Bolts holes in rear housing that hold up the drawbar plate are stripped. Any ideas?
  15. Bruce from Can.

    Stretch plastic for wrapped bales, has gone up!

    A roll of plastic will wrap 22-25 bales, and now cost $140.00 per roll. Comes out to near $6.00 per bale. Starts to feel like buying your own hay! And net wrap for the baler runs near $1.00 per bale. They sure don't give this stuff away, but when I am done using it I will gladly give it away...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top