(800) 853-2651
SHOP NOW

Recent content by Glen_in_TX

Yesterday's Tractor Forums
  1. P

    possible Jacques 60 row crop

    I have what I think is a Jacques 60 row crop tractor. It came as a rolling chassis with out tin ware or numbers except on the rear end housing. On left side 1905L and on right side 1905R. It has a T-92 Borg Warner transmission. I have a photo posted on Help Identify and Garden Tractor galleries...
  2. T

    Lift cover will not come off

    I have removed ever bolt possible and still can not get the hydralic lift cover off the 800. I even took a hoist and chain it to the lift arms, and all it did was lift the tractor off the ground. Am I missing something? Any suggestions?
  3. P

    TO-35 Overhaul Problems

    Hi Guys, Help!!! I just overhauled the engine on my 1955 TO-35. New sleeves, pistons, rod bearings, main bearings, the whole works. Reassembled it very carefully, checking clearances, and testing tightness as I went. As I was cranking it over to try to start it (I suppose I cranked for a...
  4. M

    MH 33 installing starter switch

    I installed starter switch on my MH33.There is a wire coming from the amp. gauge to the starter switch and I cannot remember which cable it attaches to (the negative or positive) I cannot get spark. I think this has something to do with it. 9
  5. A

    Is it possible ?

    Is it posible for a stock stroke factory block john deere 60 to make 75 HP ? If not what is the most ? Just looking for some ideas.
  6. G

    WICO Model C-1273

    I suppose you meant change the spring? No impulse? They rust and do break. You never recharge the magnet with spring or impulse on mag or it won't work right having to demagnetize the impulse to get it right again. A special tool was made to hold the impulse hub while removing or...
  7. G

    Moline Drill

    You'll have to figure out if it's a P, R, or S series and find a manual for it. Check manual vendors or ebay.
  8. G

    John Deere 42 combine

    According to a blue book info the JD pull type 42 combines were made 1961-1966. Called a 42 because of 42 bushel grain bin. Had 9 ft. header and 20" x 26" cylinder. 3175 was made in 1963 and 4047 in 1964. Serial numbers for 1961 began at 501, 1962 at 1501, 1963 at 3001, 1964 at 4001, 1965 at...
  9. G

    old combine

    You might some pics on Vintage Ads section too.
  10. G

    JD 4020 Hydraulic system prescreen?

    Nylon, Just bookmark this page to take you to parts catalogs. You'll have be signed in and registered with a local dealer at the the main JDparts page to use shopping cart or price parts though. You shouldn't even have to be registered or signed in to view the parts catalogs. Make sure you...
  11. G

    JD 4020 Hydraulic system prescreen?

    There is a screen on the sump pump in trans behind that plug. Some plugs are different depending on year of tractor and which trans. You'll be draining all the oil out to change, replace or clean it though so be ready with enough buckets and drain pans. The screen will be metal or plastic...
  12. G

    Rear wheel weights

    Leave the T off the end and try T21689 at JD parts catalog "where used search" and find this: Catalog Search Results 689 - 2010 (42001-) Tractor - 23Oct06 749 - 1010 Utility Tractor - 21Nov06 859 - 4020 (S.N. -200,999) Tractor - 27Jun07 970 - 1020 Tractor - 27Jun07...
  13. G

    MM 705 MF 97/95 Engine parts

    A stock MF 95 should have a MM 425 engine in it and stock MF 97 a MM 504 engine same 504 as used in MM G704,G705,G706 & G707. Propane heads used on MM tractors or irrigation engines will change compression. Maybe someone will chime in giving you the link to the MM head listings.
  14. G

    Spark Plug Gag for GVI LP

    Champion spark plug catalogs and other sources always recommended .015 to .018 gap for LPG tractors and engines. Check the timing as said in other post. The thinking is with a drier vapor type fuel you shouldn"t need that large a gap on spark plug because fuel is already more vaporized than a...
  15. G

    old shredder

    Looking again I see it doesn't have bolt holes or clamp for windrow board anyway. Maybe those were for running bundles thru to chop but why chop them like that on ground? A bedding chopper maybe? Would small straw bales or bundles go thru them before holes were welded shut? Looks too...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top