(800) 853-2651
SHOP NOW

Recent content by Goodman

Yesterday's Tractor Forums
  1. G

    Rpm.

    Thanks. That's what I have is 281 engine on a super M chassis.
  2. G

    Rpm.

    I was guessing 350. Thanks Jim.
  3. G

    Rpm.

    Out of curiosity. What's about the minimum Rpm you can idle a 450 motor down to? I've got my Super A where it will just barely put along.
  4. G

    Super M governor

    Thanks Pete. I'm not sure I know what your talking about governor fork and housing unless your saying the horizontal shaft running to the back of governor needs to be pushed in some. ??? Otherwise, Sounds much simpler than Super A. That means I can adjust it prior to running except for RPM...
  5. G

    Super M governor

    I've done several super a. This one much different. I was also told it wasn't in the manual. Don't know.
  6. G

    Norden axle

    In case anyone reads this later. Found the bearing seal and the felt seal on eBay cheaper than I could purchase bearing seal only locally. Thanks.
  7. G

    Norden axle

    Thanks. I'll check there.
  8. G

    Norden axle

    For clarity. The ones on the spindle behind hub.
  9. G

    Norden axle

    I don't think parts are available for Norden wide front axles. Where can I get replacement felt dust seals? Are the same diameter as another felt seal I could purchase.
  10. G

    Super M governor

    I've replaced the governor on super M with one that had less wear on the weight pins and spring connection points. My previous governor seemed to work well but I plan to use this one. Now how do I go about adjusting the stops and linkage on this new one? Can this be done without the tractor...
  11. G

    Water blasting

    About year ago I ask on here about sandblasting attachment for pressure washers. I didn't get much response and some seemed like they were problematic. I bought one anyway $115. Over the last year and have now completely blasted all of the super M piece by piece it has become one of my favorite...
  12. G

    230 project complete

    Great job. It is a very time consuming process that many folks are not willing to endure. But stay the course and for some of us very rewarding.
  13. G

    Char Lynn power steering

    If I had a power steering unit for Super M. Can it be tied into the hydraulic pump system or does it need separate pump? If so can a small power steering pump/ reservoir from car be rigged up. Thanks.
  14. G

    Super m governor

    Yes Barnyard I think about the hours on these old tractors often. I think someone has repaired this governor before. It has some type bushings in it. I thought initially brass. Could be copper? They are paper thin but there. Y'all have told me what I needed. I'll see what I can do. Might...
  15. G

    Super m governor

    Rustred. So the spring can be fairly tight in the hole? I can do that. For some reason I thought it needed some play. Yes that should make it respond little quicker.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top