(800) 853-2651
SHOP NOW

Recent content by govsux

Yesterday's Tractor Forums
  1. G

    Can't find radiator hoses

    Hadn't thought of that I guess if all else fails ...
  2. G

    Can't find radiator hoses

    Good idea
  3. G

    Can't find radiator hoses

    Does anybody know where I can find an upper and lower radiator hose for a 1959 TD340 International harvester crawler?? Usually a littler persistence on the internet will finally pop up but I'll be darn I can't find it. I also need a thermostat gasket but I could make one if I had to. As handy as...
  4. G

    Stuck pin

    Me again. So here's where i'm at. I actually bought a bridgeport. Been wanting one for years seems like now is a good time. I'm looking at McMasters for bushings and new idlers pin / axles. But I have a few questions need answered before I proceed. First what type of metal should I make the new...
  5. G

    Stuck pin

    id you mean stress proof?
  6. G

    Stuck pin

    If I do it correctly I shouldn't need a lathe. I will buy two new pins / axels made of 4140 eh?? 4140 is strong??
  7. G

    Stuck pin

    I am buying this used Bridgeport.
  8. G

    Stuck pin

    One of the bearing surfaces looks like this [ see pic ]. It's wore completely past the collar that held the bushing. I sm not sure how to fix this one. Either A- weld on a new collar [ which would probably break ] or B- crate a much larger collar that goes all the way out to outer rim you see...
  9. G

    Stuck pin

    Three out of the four look like this [ see pic ] They are damaged and will no longer hold a stock sized bushing. But they can be enlarged and made straight. Right now they are wore from rubbing directly on the pin / axle. I think I can fix this with my bridgeport.
  10. G

    Stuck pin

    I'll try and explain more clearly... each wheel [ idler ] has two bearing surfaces... an inner and outer. See pic.
  11. G

    Stuck pin

    I am buying a bridgeport Mill and should be able to enlarge and clean up three of the four holes then order custom sized bushings. The fourth hole is bad. Completely missing the collar that holds the bushing. Somebody here posted not to try and weld on a new collar??
  12. G

    Stuck pin

    Where are you located?? 3 out of the 4 hole for the bushings could get enlarged then order a bushing to fit. i found a place that makes them order to fit. The one side though the entire collar broke off. So for that side I am thinking I could order a 3 1/8" circular piece of steel and that could...
  13. G

    Stuck pin

    thanks. I will check with them
  14. G

    Stuck pin

    I agree I would much prefer to find used idler rather than fix. However I doubtful I can find something so old.
  15. G

    Stuck pin

    My solution I guess is to get a huge bushing then weld it all the way around.... with a hole for the axle / pin in the middle of course. I could counter sink 4 holes for bolts as well.. thoughts anyone?? This post was edited by govsux on 06/04/2023 at 06:13 pm.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top