(800) 853-2651
SHOP NOW

Recent content by GP Hansen

Yesterday's Tractor Forums
  1. G

    300/350 Utility: Anyone using 15 inch front tires? What t...

    On my 350 I"ve got 11L-15 turf tires w/6 hole rims. You can see a picture of it if you search " slow front loader on 350 utility " then click on "show entire topic".
  2. G

    growling 3 point

    Thanks, I get out my joe magee stethoscope and see what I can hear.
  3. G

    growling 3 point

    The noise quits when it's out of pto. Is this a top end fix ?
  4. G

    growling 3 point

    Come to think of it , it is quiet when I push the clutch in. With the 3 pt. down there is less growling. When I raise it up the growling is loud.
  5. G

    growling 3 point

    It's more of a growling noise then a knock. I have a 6 ft. blade on it but the 3 point doesn't have any down pressure. Are these N's supposed to have down pressure ?
  6. G

    growling 3 point

    When I lift the 3 point on my 8n it growls. Oil level is ok. Any ideas what it might be ? thanks.
  7. G

    slow front loader on 350 utility

    It"s noticibly twice as slow as the 3 point or tipping the bucket. It would take 10 - 15 seconds to raise it to full height at half throutle empty. It"s been slow since I"ve had it. The 3 point appears to be an after market one but works fine.
  8. G

    slow front loader on 350 utility

    The power steering is ran off the same pump. But would that effect it if you're not turning at the same time the bucket is being raised ?
  9. G

    slow front loader on 350 utility

    Raising and lowering the bucket is very slow. Doesn't jerk. It's full of hyd. oil. Tipping the bucket is ok. The 3 point is ok. I'm thinking it's not supplying enough oil fast enough for 2 large rams.
  10. G

    slow front loader on 350 utility

    The loader is so slow. The hyd. pump is on the distributor. Do most front loader pumps run off the crank? I'm thinking the pump doesn't have the capacity for the large rams.
  11. G

    The two M brothers

    Central Washington. A bit far.
  12. G

    The two M brothers

    The tractor on the right gave it's all so it's brother on the left may live a few more years.
  13. G

    Toy box

    My guess it"s about 36 x 60.
  14. G

    Farmall H restoration

    Thank you Sweetfeet, this will help.
  15. G

    Farmall H restoration

    Great slide show. I"m still trying to figure out how to post a single picture.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top