(800) 853-2651
SHOP NOW

Recent content by Greyhound101

Yesterday's Tractor Forums
  1. G

    Parts for disc harrow

    Pics for identifying the maker of the harrow.
  2. G

    Parts for disc harrow

    Yes, cutting the 1.25" nut and replacing with a new nut would work. Guess I'd just rather use a couple wrenches to break the nut loose rather than have to cut and touch up threads. To each their own I suppose. I was able to locate a spool that will fit my square shaft. A friend had a pile of...
  3. G

    Parts for disc harrow

    Sure, that would work to tighten the nut but to loosen is a different story. Three of the five blades were missing (broken) so there were only two left on this particular gang. It took a large pipe wrench on the only spool that wasn't damaged to prevent the axle from turning and a wrench with...
  4. G

    Parts for disc harrow

    Shaft size is 1.25"
  5. G

    Parts for disc harrow

    Just tried Shoup, no luck.
  6. G

    Parts for disc harrow

    What are you using to prevent the axle from turning while you tighten/loosen the nut?
  7. G

    Parts for disc harrow

    I'm a former tooling engineer so I completely understand how to hand-craft a simple part such as a spool. Due to the relatively short length of spool that I need (4.5"), I'd like to have more spool-to-axle engagement than 1/4" or so on each end of the spool that I would have if I were to use...
  8. G

    Parts for disc harrow

    I'll try to get some pics on here later this evening.
  9. G

    Parts for disc harrow

    I have a machine shop at my disposal but the problem is the square thru hole for the squared shaft. It would require a LOT of machining time to build inserts for a squared shaft which is why these parts were cast to begin with most likely.
  10. G

    Parts for disc harrow

    I'm in the process of rebuilding one gang of my disc harrow. Problem is, I have no idea who the manufacturer of the harrow is. I've been unable to find any identification numbers and there's no paint to give me any idea of brand. What I'm needing is a spool piece to replace one that's broken...
  11. G

    4610 charging problems

    Is the batt sensor internal to either alt? Also, what is necessary to change to the Delco? Are there wiring instructions you could point me to?
  12. G

    4610 charging problems

    4610: What simple checks can I make to determine whether the alternator or voltage regulator is bad? What I'm seeing on my voltage gage (I mounted an external gage in the dash) is battery voltage for most of the time and then it'll jump to 14v for a few minutes and then back to batt voltage...
  13. G

    4610 alternator wiring

    Ok, thanks. I'm hoping there's a break in the wiring between the alt and the regulator. If the alt is the problem, I'll be back on here asking how to convert it to a Delco. Thanks again.
  14. G

    4610 alternator wiring

    Do you know if it has an internal regulator?
  15. G

    4610 alternator wiring

    Looking at the back of the alternator, can anyone tell me what each of the wires are (position 3 has two wires) and where they terminate so I can trace them? I'm hoping one of these wires is either damaged or broken and it's causing or contributing to my voltage stabilization problem. Thanks.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top