(800) 853-2651
SHOP NOW

Recent content by GunnyIa

Yesterday's Tractor Forums
  1. G

    Need oil pump rebuilt - recommendations or opinions?

    TOH, I've been following this forum for quite awhile, and trust that you would do an outstanding quality rebuild. When I get around to pulling the pump, I'll send it off to you. Email me your address to [email protected] and let me know your pymt choices. Thanks to all for your comments...
  2. G

    Need oil pump rebuilt - recommendations or opinions?

    Hi all, Been awhile since I cruised these waters! My 1948 8N has NO oil pressure. I'm getting ready to drop the pan and get the oil pump rebuilt. Any opinions on where or who might be interested in doing the work? Appreciate any & all feedback! Thanks! Gunny in Iowa
  3. G

    Car Acronyms

    I once had a Ford pickup. Would never admit to owning a Ford (I'm a GM person). So I changed the tailgate to a chev tailgate, and where the side 150 stuff was, I put "Chevord 1500". Sure caused some conversations! Gunny in Iowa
  4. G

    Weed & grass killer - round-up?

    I am North of Muscatine, about 3 miles South of Moscow, Iowa. I am not against a road trip, we love to take a day and just roam the country-side. Gunny in Iowa
  5. G

    Weed & grass killer - round-up?

    I have a tool (sprayer) that I pull behind my New Holland GT22. I mix weed-be-gone with 25 gal of water and spray the weeds in the lawn. I get good results, kills creeping Charlie too. I want to spray and kill the grass growing in our gravel driveway. Neighbors tell me they have little...
  6. G

    Stuck clutch what would you do?

    Royce, I think I found the "seal" you are referring to, part # 8N7052A ? Would NAPA carry this, or must I order from this site? The bearings came with the clutch kit, which also came from this site. The throwout bearing is in a box with "ATLANTIC Quality Parts" on the box. Since it came from...
  7. G

    Stuck clutch what would you do?

    Thanks Tall T, I was using the wrong upload area. Just to test it out, this is the flywheel before cleaning. Sorry for the fuzzy pic, it's the cameras fault! Gunny, in Iowa
  8. G

    Stuck clutch what would you do?

    Hi again, Their was no oil on the flywheel, it was dry and had pieces of clutch stuff stuck so tight it took a sharp chisel & hammer to get it off! I then used a wire brush to polish the flywheel. Ater cleaning, I closely inspected the flywheel for cracks, saw none. I've watched U-tube...
  9. G

    Stuck clutch what would you do?

    Hi again, Well, I tried all the tricks and none worked. So I split the tractor today and wow, was that clutch stuck! I got it loose then off the tractor. The new assembly is here and ready to install. It's a hair past 2 PM, so a nap is calling. Will clean up the flywheel tomorrow with a...
  10. G

    New Holland GT22 - HELP

    Hi again! I'm doing a good job answering my own questions! Hope this helps someone else, too. The tight bolt at the end of the shaft turned off CCW, after I put a cheater bar on it. Didn't break, thank goodness! The clutch then came off in pieces. Looks like the electrical connection is...
  11. G

    New Holland GT22 - HELP

    Hi all, I may have found the problem? Their are two loose and not connected wires near the mower clutch on the drive shaft. I'm wondering if it is an electric clutch? Looks like it may be, and the wires pulled loose when the battery was changed. The bolt that goes into the end of the motor...
  12. G

    New Holland GT22 - HELP

    Deck has no safety switch.
  13. G

    New Holland GT22 - HELP

    My New Holland GT22 has a 52" mower deck. To start the deck, you pull out a knob on the dash. The tractor is hydraulic drive. It worked great last Fall. Today I installed the mower deck & belts. When I pulled the knob to start the blades, nothing happened! Any suggestions on where...
  14. G

    member map New Salem, North Dakota

    Onefarmer, I tried to move my location, then tried to delete it because it was at the wrong location. Couldn't get her done. Could you delete my "GunnyIa" entry in downtown Muscatine, Iowa? I've put a new pin marker NW of Muscatine on the Cedar River. Appreciate your help, & thanks...
  15. G

    member map New Salem, North Dakota

    Onefarmer, I tried to move my location, then tried to delete it because it was at the wrong location. Couldn't get her done. Could you delete my "GunnyIa" entry in downtown Muscatine, Iowa? I've put a new pin marker NW of Muscatinen on the Cedar River. Appreciate your help, & thanks...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top