(800) 853-2651
SHOP NOW

Recent content by Hayrack

Yesterday's Tractor Forums
  1. H

    case 1030 ck 3point lift capacity

    I hooked my 830 up to the snowblower this winter and didn't realize it was frozen down until I went to pick it up. She had NO problem pulling the front end right off the ground with 350 lbs of front weights on it. My estimation on what will a Comfort king lift on the 3pt that it doesn't matter...
  2. H

    Electronic Ignition For 3010

    I have the electronic ignition setup in 3 tractors and have put it in several others for other people. I have never had an issue with them and they all start and run better than they ever did. My 720 LP gave me a fit for the first time in 5 years this spring. Replaced the cap, rotor and plugs...
  3. H

    jd 965 wagon - need part

    Pics would definitely help. I have never heard of a 965 gear. Just a 963 and a 1065 so it is making me wonder what you have. Is it a casting or a fabricated steel piece? The 963 had welded steel and the 1065 was cast steel.
  4. H

    WD-45 repower

    I am with Aaron on this. I would just go back into that 226 and find that power. I rebuilt one for a guy a while back using a set of 4 1/8 D17 pistons and sleeves. That old girl would put out 67 HP on the dyno with a D17 governer.. The power is there, you just have to find it and its all in...
  5. H

    Mechanic Needed for 1949 BW

    If you guys don't find anyone closer, I may be able to help. My email is open.
  6. H

    Deere Musuem

    I had the pleasure of getting to drive that Dain. Frank Hanson was a great guy!
  7. H

    Round baler gearbox leak

    I have done it with good results but John Deere cornhead grease works just as well.
  8. H

    Rd hay baler sales in USA & World

    Around here, ( South East South Dakota)it is about a tie between New Holland and Deere. No Vermeer dealer close so you don't see very many at all.
  9. H

    Buying First 2 cylinder?

    If you are going to buy one... There are several things to watch for. The best way I can think of to check for a worn shift or transmission is to shift it several times from one side of the quadrant to the other and see if it misses the overdrive. Check the clutch components for wear and that...
  10. H

    IH 2A Hay Crimper

    The weight of the machine keeps the cylinder pin in the slot. It is designed that way so that if you happen to go to low with the machine that it wont lift the wheels up. Yes, you must have a cylinder on the machine. I have deal that I tried on mine that looks like a ratcheting load binder but...
  11. H

    ** WORKING Calendar question **

    You can put me down for both!
  12. H

    first crop, nc wis

    Yup... Sure looks like a Case from this side...
  13. H

    CASE 930 lp

    If you hear gas coming through, your diaphragms in your vaporizer are bad and it needs to be rebuilt or replaced. It started on the rich mixture surprisingly but wont run on it because those diaphragms that are leaking are also acted on by engine vacuum to control the mixture of LP and air in...
  14. H

    JD 6420 and 6430 good, bad and ugly?

    We have been looking to update our loader tractor and have been looking at a few 6420 and 6430 FWA outfits. Most of them are PowerQuads but we did look at one IVT trans. Most of them have been in the 4 to 6 thousand hour range. Who is running them and have they had any issues?? Thanks in advance.
  15. H

    case 411b - no clutch when trying to shift into gear

    The Caseomatic is a little different than most other tractors. They are not supposed to be shifted above idle. To start out, With the engine at idle, press the inching pedal (clutch pedal) and place the transmission in gear. Then, let out the inching pedal. Then, give it some throttle to get...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top