(800) 853-2651
SHOP NOW

Recent content by henry g

Yesterday's Tractor Forums
  1. H

    Looking for an AR John Deere

    Searching for an electric start unstyled AR on steel. Not seeking an restored tractor, just a runner or one that is unstuck. Nothing shown on photo ads, ebay, etc. Thanks
  2. H

    A-60 Clutch Assembly

    Might be a silly question, but will a late Model A with the six speed tranny's clutch assembly work in a 1953 model 60? Im talking belt pulley and all internal drivers, disks, and facings? Thanks.
  3. H

    60 oil pressure

    Yes its connected correctly..Which fitting are you referring to?
  4. H

    60 oil pressure

    The gauge has no reading and the gauge functions on the other tractor. The oil looks fine and is 5W 30. When running the oil pours out where the the gauge line was disconnected, I would think it should shoot out for a lack of a better term..
  5. H

    60 oil pressure

    Hi, I purchased a running 60. The tractor I assumed had a bad oil pressure gauge, so I stuck a working one on it. The old oil pressure fuel shut off had been eliminated. After changing the oil pressure gauge, still had no reading. Removed the line and oil would pour oil the fitting but not shoot...
  6. H

    Carb Question

    Thanks for the analysis. Now, the 33, 53, 71 and 72 have the same size venturi, but the 51 is an 1/8" bigger I believe. With the throttle and choke blades all being the same size, do you think that increase in venturi size helps all that much?
  7. H

    Carb Question

    What are the differences in a DLTX 33 vs a DLTX 71. I know the choke mechanism is different, my question is about performance on a enhanced engine. Im looking for the carb that will perform better and why.
  8. H

    Otto Gas Engine works

    Anyone had trouble getting in touch with him? Trying to order some rings and have been unable to reach him by phone. Thanks
  9. H

    dltx duplex carbs

    Are these carburetors slow to responding until the tractor warms up? I have to leave it partially choked until the tractor warms up then it will run fine. When you first start it it wants to die or cut out until the engine has ran and warmed up. Or.. do I have an internal or settings problem? It...
  10. H

    70 gas question

    How could I get a 8.5:1 compression ratio? The F900R cam has been reground stock, and I'm using LP pistons. Will that get me there? Do I need to mill any off the head? I plan to relieve eyebrows and port match. Will the fixed jets in the Carb be sufficient for these gains? Thanks.
  11. H

    70 gas questions for buick and or anyone else

    How could I get a 8.5:1 compression ratio? The F900R cam has been reground stock, and I'm using LP pistons. Will that get me there? Do I need to mill any off the head? I plan to relieve eyebrows and port match. Will the fixed jets in the Carb be sufficient for these gains? Thanks.
  12. H

    DLTX Duplex Carb Question

    I am having trouble installing the spring on the choke shaft and lever. I seems it would only go on one way, but when I install it, the choke butterflies are not level, they are slightly raised toward the choke position. If I pull back the choke lever, it goes into the choke position as normal...
  13. H

    Long winded 70 gas question

    Recently purchased a 70 gas tractor. Tractor smokes,needs ringing but runs fine. The timing was set very late, so I adjusted it to sparking at TDC. Now the tractor runs even better, BUT it knocks when you accelerate the engine. It does not knock at low idle or high idle, but only when you crack...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top