(800) 853-2651
SHOP NOW

Recent content by henry rit

Yesterday's Tractor Forums
  1. H

    w-9 motor in a m?

    thanks I figured no because ive never seen one at any pulls
  2. H

    w-9 motor in a m?

    I was wondering if the w9 motor will bolt in a farmall m.
  3. H

    There's alot of stupid tractor pullers out there.

    I ran into this at the last pull. they allow 200#'s over (that I think is bs), when I went to the scales for the 6500# class I was 6760# I got off to pull a weight and the guy running the scale said your fine close enough, I was thinking to my self as I pulled off the scales why do they even...
  4. H

    hp? to pull 2nd gear

    I was wondering how much horse power it will take to pull my m in 2nd gear in 6000-7500# classes if its possible. I currently can pull 5000,5500# in 2nd gear the motor is working hard by the end of the track but I still spin out. I'm planning on redoing the motor this winter but not sure how...
  5. H

    100 hp m?

    I'm looking to build a farmall m around 100hp any suggestions on getting there and where to get the parts.
  6. H

    good pulling tire?

    I've been trying to decide what tire's to buy for my farmall m I currently have 15.5-38's on 14" rims but was thinking of going to 14.9's and have been tossing up about 23 deg. or field & road's but someone told me to put 45 deg. tires on it. 95% of the tractor's run field and road. but none run...
  7. H

    jd730 vs farmall m

    the class speed limit is 3.75mph the jd is stock and the m was tuned in on the dyno at 52 hp. the jd is on 18.4/34's the m is on 15.5/38's also the jd is pulling from the draw bar and the m is pulling from the loop both set at 19"
  8. H

    jd730 vs farmall m

    was wondering how a farmall m would stack up against a jd 730 diesel in div 2 8500#class
  9. H

    weights on a m

    Im gonna try pulling my m for the first time and was wonder if I should run wheel weights or start off hanging weights on the brackets I have a weight bar across the back and one where the motor meets the bell housing planning on 5000? 5500-7500# C-classes,thanks
  10. H

    1930 Farmall Promotion Film

    that was a cool old video
  11. H

    super m seat on a m?

    I was wondering if its possible to mount a super m seat on a m. I wanted to move the battery under the seat.
  12. H

    farmall m dyno ?

    I guess for now I"m going to leave ever.ything set the way it is . I"m going to pull it for the first time this weekend I"ll see how it does
  13. H

    6600 Transmission

    I can look tomorrow morning to see if we have a shop manual still when I get to the shop.
  14. H

    m wont shut off unless idling?

    it is a three wire, a buddy of mine told me his grandfather always puts a light on his tractors when he converts them to 12 volt, so that's probally why.also I don't have a resistor on the coil it is 12v but should I? thanks
  15. H

    farmall m dyno ?

    I have a 46 m with a distillate head it has 100psi of compression everthing ive found is that's high for a distallate head.Ive never had the head off to see what the pistons are. but I dynoed it yesterday,drilled the main jet out 2 sizes bigger. ported the venture out bigger and messed with the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top